Art Dent Posted August 31, 2018 Share Posted August 31, 2018 Hello folks, As a new entrant to the world of O-Gauge (aka 'Senior Scale' ) I have a question regarding suitable power supplies for DCC-equipped locos. I think I know the answer to this but there's never a daft question if you don't know!I have a NCE PowerCab throttle and power supply board which I use with my OO-Gauge locos.This will be OK to use with O-gauge won't it? (obviously not at the same time!)Assuming I am correct and it will, how many sound-fitted O-gauge locos can the PowerCab system handle? I'm looking at 3 sound-equipped locos 'running' at maximum plus some colour-light signals and up to 3 points with 'Tortoise' type 'stall' motors on a 6ft x 2ft plank (possibly running up to 10ft). I'm not planning on running any large Heljan double-motor locos, nor hauling anything heavy and if needs be I have a (currently unused) NCE SB5 Smart Booster.Thanks in advance,Art Link to post Share on other sites More sharing options...
birdseyecircus Posted August 31, 2018 Share Posted August 31, 2018 My NCE power cab will handle two Heljan DCC sound locos moving on a end to end layout. Paul Link to post Share on other sites More sharing options...
Art Dent Posted August 31, 2018 Author Share Posted August 31, 2018 Thanks Paul, That's good to know. Are these single-motor Heljan locos or larger two-motor jobs? Art Link to post Share on other sites More sharing options...
Simond Posted August 31, 2018 Share Posted August 31, 2018 (edited) This will be OK to use with O-gauge won't it? Yes... Probably! I’d expect it will do everything you require Best Simon Edited August 31, 2018 by Simond Link to post Share on other sites More sharing options...
F-UnitMad Posted August 31, 2018 Share Posted August 31, 2018 The 'basic' NCE Powercab is only 1.2 or 1.5 Amps output I seem to recall. I played safe and bought an NCE SB5a Smart Booster to go with it when I went DCC with my American O Scale stuff. Better safe than sorry. Link to post Share on other sites More sharing options...
Art Dent Posted September 1, 2018 Author Share Posted September 1, 2018 (edited) Thank you Simom and F-Unit The 'basic' NCE Powercab is only 1.2 or 1.5 Amps output I seem to recall. I played safe and bought an NCE SB5a Smart Booster to go with it when I went DCC with my American O Scale stuff. Better safe than sorry. According to NCE themselves (link: https://ncedcc.zendesk.com/hc/en-us/articles/203935645-Adding-more-power-capacity-to-the-Power-Cab ) the PowerCab shuts itself down when the current draw exceeds 3A (the current output is apparently dependent on the power supply). The power supply supplied with the PowerCab is rated at 13.8V DC, 1.8A output. I have a SB5 booster which I bought with the PowerCab. So far, the SB5 is unused. Probably best to run the Dapol 08 on the PowerCab with an ammeter to see what the current draw is. As the voltage at the rails (the output of the PCP) is not true AC but a PWM-modified AC, a digital multi-meter will not give a true reading of either the rail voltage or current, however you can monitor the DC current draw between the power supply (PSU) and the PowerCab Panel. Cheers, Art Edited September 1, 2018 by Art Dent Link to post Share on other sites More sharing options...
birdseyecircus Posted September 1, 2018 Share Posted September 1, 2018 Thanks Paul,That's good to know.Are these single-motor Heljan locos or larger two-motor jobs?Art Yes twin motor locos. Paul Link to post Share on other sites More sharing options...
Fastdax Posted September 1, 2018 Share Posted September 1, 2018 Probably best to run the Dapol 08 on the PowerCab with an ammeter to see what the current draw is. As the voltage at the rails (the output of the PCP) is not true AC but a PWM-modified AC, a digital multi-meter will not give a true reading of either the rail voltage or current, however you can monitor the DC current draw between the power supply (PSU) and the PowerCab Panel. There is a built-in Amps display on the PowerCab. I don't know how accurate it is but I can see a current draw of 0.24A just after switch-on, dropping to 0.08A after a few seconds as all 3 stay-alive locos have finished charging up. From the main display, press "PROG ESC" 6 times, then ENTER to "SET CAB PARAMS", then press 1 for "TRK CURRENT". Use "PROG ESC" to get back to the main display after doing this. It has an annoying habit of resetting to the time-of-day, but it's quick to change it back to track current mode. Link to post Share on other sites More sharing options...
Art Dent Posted September 1, 2018 Author Share Posted September 1, 2018 There is a built-in Amps display on the PowerCab. I don't know how accurate it is but I can see a current draw of 0.24A just after switch-on, dropping to 0.08A after a few seconds as all 3 stay-alive locos have finished charging up. From the main display, press "PROG ESC" 6 times, then ENTER to "SET CAB PARAMS", then press 1 for "TRK CURRENT". Use "PROG ESC" to get back to the main display after doing this. It has an annoying habit of resetting to the time-of-day, but it's quick to change it back to track current mode. Ahh ... yes. I'd forgotten about that! Thanks for reminding me! Art 1 Link to post Share on other sites More sharing options...
F-UnitMad Posted September 1, 2018 Share Posted September 1, 2018 Yes one downside of using a booster is that the amps display doesn't work. Link to post Share on other sites More sharing options...
Guest teacupteacup Posted September 1, 2018 Share Posted September 1, 2018 My friend runs his exhibition layout (St Marnock) with an NCE Powercab, all loco's sound fitted (some with smoke), including double motored Heljan diesels, Never had a problem with overloading the power supply, even running 2 HJ locos together and other loco's on shed with sound running. Its a very capable controller Link to post Share on other sites More sharing options...
Art Dent Posted September 1, 2018 Author Share Posted September 1, 2018 My friend runs his exhibition layout (St Marnock) with an NCE Powercab, all loco's sound fitted (some with smoke), including double motored Heljan diesels, Never had a problem with overloading the power supply, even running 2 HJ locos together and other loco's on shed with sound running. Its a very capable controller That's good to know TC, thanks Art Link to post Share on other sites More sharing options...
RMweb Gold jcarta Posted September 25, 2018 RMweb Gold Share Posted September 25, 2018 Good Evening Art I'm not the connoisseur when it comes to DCC, however, I also use the NCE power cab with a 5 amp booster & some Heljan O gauge loco's..... As for how many loco's you want it to control will depend on the software chip that you have installed in the throttle, version 1.65 will allow you to control up to 6 loco's at any one time but you will have to set these up on the throttle menu. Originally I had a shunting layout in the garage (17'x2') layout and never had a problem. We then extended the layout to run around the garden but we did have to utilise the 5 amp booster and start to put the layout into power districts, we also utilised a Merg booster to operate numerous loco's on the layout and since installed we have not really had an issue, (weather permitted) something I then left to my colleague as he has the knowledge of the intricacies of how DCC works and what gives us the most to operating the system. Originally we also operated tortoise points and I believe signals via the power cab but have since change this to operate the points / signals via a control panel with the help of Merg components. If you require any further assistance I can ask him to comment on your forum page... Jim Link to post Share on other sites More sharing options...
RMweb Premium Ray H Posted September 26, 2018 RMweb Premium Share Posted September 26, 2018 I would be surprised if you found problems with just using the PowerCab. We've had three sound equipped twin motor Heljan locos moving around a 40 feet by 20 feet continuous layout relying on just rail joiners - i.e. no power bus - without any problems. I'm not sure that you could control three moving locos on your own on a shunting plank whereas 3 locos of which one or two are moving plus the other's being stationary with their sound active should be easily achievable. Hope that helps. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now