An odd title you make think, but I shall explain.
Firstly the real one. The CR had large numbers of pig iron wagons, in practice used whenever a low sided wagon was needed. Another of those general types you can never have enough of. This example is built from the 51L kit, though I have used my usual method of a copperclad sub chassis for the W irons and sprung buffers.
Ok, the imaginary wagon. I mentioned that I cut some extra bits when I made
For various reasons this one has taken a while to finish. I had a bit of a fight with the lettering, harsh closeups show my errors.
I wanted to weather it as photographed in the wagon book with the lime getting well into the grain of the timber. That was done with rotring white ink and powders, my lack of weathering skills shows up, but it gives the right overall impression I think.
A few pictures in the on the layout;
Back at the bench again. The Caledonian built 40 Dia 25 lime wagons from 1886 to 1888. They were essentially a Dia 22 mineral wagon with a roof.
The CRA do a drawing of it, which gives the wb as 8’6’’. I don’t think that is correct. The Dia 25 is essentially a Dia 22 mineral wagon with a roof, and they are definitely a 7’9” wb. The Diagram book gives the Dia 25 wb as 7’9” as well.
So I scanned in pics of both types of wagon, scaled them to size and superimposed t
There are some things which just don’t scale, no matter what you do the real thing looks wrong in model form. Smoke and water are the obvious ones, but I’l add another. Dust. Scaled down they are not particles, they are lumps.
So I have been enjoying running the railway a bit, collecting info and deciding what to build next. However I couldn’t help noticing that the station had become a bit dusty and once you have noticed it it sticks in your eye. Time for some cleaning, after all we
There are times when I can see the appeal of BR unlined black. About half way through decorating the No. 252 was one such occasion. However bit by bit it all came together. The final result is a bit bright, but the brass does tend to develop a patina of its own over time. As ever close photos show errors the eye misses and it needs some builders plates as well.
A few pics ;
Or
The correct gears arrived and so with a fully assembled and tested gearbox I have been able to push ahead. Soldering needs a bit of a clean up, but thats the chassis built up and running smoothly. Driving the front wheelset means I can have a compensation beam at the rear. The kit suggests driving the centre axle, since driving the front axle would mean losing the view through under the boiler. However by using a roadrunner box and an extender with a narrow motor I was able to get the motor righ
Well, there we are, a slap of paint makes all the difference.
Rivets are Archers, easy to apply and they make a big difference on a model like this. No idea what is under that sheet, but it is heavy so this wagon moves as if it does have 16 tons on top. The chains and shackles were fiddly, but add to it all I think.
Catching a bit of evening light.
You can see that this wagon is properly sc
Progress on the 670 is delayed at the moment until I get the parts for the gearbox. Can’t be helped, difficult times slow things down.
Anyway, I need to build something. I had a browse through drawings and books and settled on a D27 Machinery wagon. ( the CRA does sets of wagon drawings on a cd )
So with a bit of luck here is one I can make from the stuff I have. The body is laminated from 10 thou styrene cut on the silhouette. Bit of an odd wagon, big plates on the sid
The engine body is not far off complete. A close photo shows areas that need some cleaning up. The gap between the rear of the boiler and the cab needs to be filled, the cab is square to the footplate so I’m not sure how that bit of drift happened.
As you see there are a lot of holes, but I have the pipework bent to shape ready to go on post painting.
The frames are ready to go. The cylinders have been moved out slightly and solid brass cross pieces and
I have added a bit of scenic detail to that corner. Much improved in taking the eye round at the end of the viaduct. I am going to have a go a tree making to disguise the rather abrupt end of that big retaining wall, but for now thats the layout back together and some trains running again.
A couple of rough snapshots.
Hope everyone is managing in these strange times.
I have been with pottering on with the far corner of the layout, signals are installed, then unplugged and a lightweight scenic extension knocked up from foamboard and card. All a bit rough at the moment, but taking shape. I think it will enhance that corner and take the eye round to the storage yard in a more transitional way. Some sort of wooded area perhaps.
I also painted a couple of figures and added them to this very odd thing that I made quite
So like many I’m stuck inside unable to work, so keeping optimistic I’ll treat it as a rehearsal for retirement. Time to take stock, have a good dig through all the boxes and see what I have available to make things with.
Signal parts come on frets or bags of several bits. Of course all the spare bits are put away, so having sorted through them I realised that I had enough bits for a couple more signals. An ideal project, fiddly and time consuming. Takes the mind off other things.
These are made from the latest True Line Models resin body produced by the CRA. Many thanks to all involved.
The description pre-diagram means that they were built bfeore the introduction of the official diagram book and therefore don’t have a diagram number. More details here;
https://www.crassoc.org.uk/forum/viewtopic.php?f=17&t=1479
I have built them in my usual way, copperclad sub chassis, rocking W irons, internal sprung buffers, all the bits from 51L
A pair of these control movements across the trailing crossover beyond the platforms. The Stevens pattern dropflap signals themselves are the 51L etch, I had them powered with a servo via a linkage. It was designed to cope with servo overthrow under transient conditions, but it didn’t. So for quite a while now they have been cosmetic. Time for a rebuild.
The signals are mounted on a bit of double sided copperclad with some 6mm U section brass on the other side. The flap and conterwig
Following the excellent discussion on the storage of lamp oil I have built a combined lampmans hut and coal store.
A dimensioned sketch of the type favoured by the Lanarkshire and Ayrshire ( and other CR lines built later on ) can be found in "Signalling the Caledonian" by Jim Summers. A very common feature in many stations and yards, clearly having a separate small building for maintaining signal and general lamps would minimise damage by fire should an accident occur.
Some photos of the brake wagons. Both have a rather rough appearance, but I doubt they were high up the list for maintenance.
I have made a few guesses about the final finishing.
Firstly, I’m not sure about the running numbers. I know that No. 185 was of this type so I have just used a couple of close low numbers. Being built on early wagon frames they might just have been painted on rather than having number plates.
Secondly,
I have pushed on a bit with the brake wagons, just about ready for some primer. They are small, but I have managed to get enough weight in there for them to run smoothly enough and keep the compensation working properly.
Here’s a harsh picture of the underside, nothing particularly special but the use of a copperclad sub chassis does give decent fixings for W irons, ajs and the buffer springs and allowed me to get a slab of 1mm brass in as a spacer. Brake gear is a chopped up etch fr
Happy new year to everyone.
So not one for celebrations and fed up with the dead time twixt Christmas and New year I decided to make something. I looked about and ferreted in various boxes, what did I have at my disposal? One last sheet of 10 thou styrene. An idea formed, a brake wagon. Something that has been sitting in the back of my head for a while. So I dug out the wagon book, scanned and sized the the drawing and re-read the section about them in the book and the CR forum.
I have been sorting out the western end of the layout so the boards have been wheeled out for access. Getting a bit chilly this time of year so pvas do take a while to dry for the scenic stuff.
Anyway, a few pics of that corner. I’m not entirely happy with the brick gable end of the factory. I keep an eye open for something more suitable but as ever its the problem of getting a good square on photo of it.
The signal box on Kelvinbank consists of a photo of Boness box stuck to a light bulb box. Ok, its the right style and size, but time to make something a bit more accurate.
So the silhouette has been busy. The windows are all done as a single layer, the frames both sides laminated onto that. Cutting all those soffit brackets took a while, but I’d never manage it by hand. This is the second attempt, I got my dimensions wrong on the go.
Some brickwork for
Well there we are, No. 203 in service. It looks all right from a distance, but harsh close ups show my lining inabilities. I did try some of the 2 part Fox transfers where you overlay black on a red/white line, but I just couldn’t get them to look right. The CR red/black/white was subtle with fine lines, hopefully one day a transfer maker will take pity on us.
Then again what matters is how it runs
It was gloomy yesterday so I turned the layout lights on and tried running a few trains in the dark. Daft, but oddly fun.
Anyway, a few random pics of variable quality. The station in general, I need to lightproof the roof more next time it is off.
This is a lucky pic. I cant really see the from of the station building so its just done by point the cam
Another go at a sheeted wagon. Fair criticism of the way my early attempts at roping sheets down led me to consider a more realistic way of doing things.
Looks a bit better in terms of roping, but I think I could improve the sit of the sheet itself.
The starting point is a CR D15 dropside whitemetal kit from 51L. This is made up in my normal fashion. However in order to tie the ropes down I ne
Right, back to some modelling. I have said painting is not my forte, add full size painting to that too. Anyway, a scotch derrick. I made this a long time ago for the previous layout, but I haven’t got round to fitting it since its a bit vulnerable as it is towards the front of the layout.
Scotch derricks are a simple crane, they were used in large numbers throughout the railways and industry in general. Drawings of the size preferred by the CR were published in “The true line “ and
Scenic work is not something I am very good at, but there we are a gap filled. I wanted it to look like one of the old estates that got enveloped by the progress of Glasgow to the west but has yet to be developed. The result is some lengths of very old boundary wall in some odd locations if you dig about in the area.
Anyway, it fills a gap.
If you are going to have a gate, you might as well have a working one.
