grahame Posted March 12, 2018 Author Share Posted March 12, 2018 Hi Grahame, just a thought how about making a conical mould from waxed card and filling it with polyfilla, All the best Adrian. A possibility, and even casting in resin (which I've done in the past) rather than polyfila. I could even use a slightly larger funnel as the mould for casting. So many options now. But while I wait for the funnels I ordered I've cut the roof tent coverings from card. The ones that overlap the towers are not glued in place to allow for trimming them to accommodate the turret conical roofs. The dark marks on the card is where I have soaked/smeared superglue in to strengthen it. The flat surfaces will be covered with Redutex tiled adhesive sheets so having the card parts removable will be useful as a template for cutting the Redutex to fit: G. 6 Link to post Share on other sites More sharing options...
grahame Posted March 15, 2018 Author Share Posted March 15, 2018 The funnels arrived this morning. Unfortunately they're probably a little too small (and I couldn't find any slightly bigger): So I razor sawed off the spouts and trimmed away the lips and handles. Then I cut circles of 0.25mm thick plasticard and wrapped it around them to make them a little bigger/longer and cover the missing tops where the spouts were. Sounds easy but in reality it was quite a struggle as the plasticard, despite being thin, wouldn't sit flat against the funnel - it seemed to buckle up and flare out (instead of neatly butting up at the seam) and even caused the centre (top) to split and tear. Getting it in place involved copious hacking, glue, filler, swearing, painting, cursing, refiling, more glue, bashing and even cutting my finger which added blood to the mix . . . . . In the end I managed to produce two roughly conical roofs that look similar and are approximately the same size. I don't think I'll bother trying to add tile effect relief - paint will be fine: Next to trim the flat roof sections to fit against the conical roofs. Ahhhhhh. G. 7 Link to post Share on other sites More sharing options...
grahame Posted March 15, 2018 Author Share Posted March 15, 2018 A bit of cutting, a lot of superglue and plenty of cussing and the flat roof sections are on - with the front parts covered with the last of my Redutex tile supplies. The slight gaps will get covered with ridge tiles and flashing. I had to add the top floor tower windows as they can't be reached from the bottom before gluing the conical roofs on. I just hope they don't get ruined when I get some paint, weathering and varnish on the brickwork: And surprisingly it's starting to look like Aston Webb House. G. 9 Link to post Share on other sites More sharing options...
RMweb Gold Royal42 Posted March 15, 2018 RMweb Gold Share Posted March 15, 2018 (edited) This is a very interesting thread and, although I haven't read every post yet, there are some good ideas which I can learn from. I build my models to two scales: aircraft to 1:144 scale and ships to 1:350 scale. One of my projects for the aircraft is an airport terminal and I've been plodding with this, on and off, for a while now. The building is the terminal at Elmdon Airport The facade is shaping up nicely Quite a few windows! The middle deck area still needs to have the 'wing' shelters constructed; plus the another gallery deck to be added above the restuarant on the right. It is a bit amateurish compared to some I've seen on this thread but I'm enjoying myself. Mike Edited March 15, 2018 by Royal42 9 Link to post Share on other sites More sharing options...
grahame Posted March 15, 2018 Author Share Posted March 15, 2018 It is a bit amateurish compared to some I've seen on this thread but I'm enjoying myself. Not really. It looks neat and tidy, and representative of the real building. The thing with what appear to be complex buildings is to break them down in to simple standard geometric shapes that can be made individually and then brought together. Then colour and finish will help complete it as one structure. G. 2 Link to post Share on other sites More sharing options...
grahame Posted March 15, 2018 Author Share Posted March 15, 2018 The next, and probably last main constructional stage before painting and glazing, are the two stripy tall chimney stacks, one on the side of each turret roof. Below is just a very rough mock up from folded card as to where they go (for one side).The main consideration is how to fix them in place - do I make them shaped to fit and attach to the conical roof (probably very tricky) or do I cut holes in the roof for them to sit in (also tricky). I'll make them first and then decide: G. 6 Link to post Share on other sites More sharing options...
Marly51 Posted March 15, 2018 Share Posted March 15, 2018 (edited) I was looking back at your first photograph of the whole building to check those chimneys - in reality, they look odd and blocky, but I think it is because they are quite a contrast to the round towers with their conical roofs, which have a certain elegance! Edited March 15, 2018 by Marly51 Link to post Share on other sites More sharing options...
grahame Posted March 15, 2018 Author Share Posted March 15, 2018 I was looking back at your first photograph of the whole building to check those chimneys - in reality, they look odd and blocky, but I think it is because they are quite a contrast to the round towers with their conical roofs, which have a certain elegance! Yep, they are quite a statement, and being decorated with contrasting stripes makes them stand out. In addition there is another statement chimney stack in the centre at the back of the pitched roof which is quite difficult to see from pics of the front taken at ground level. This photo is taken from behind it (in a sort of courtyard) looking forward - you can just see the top of the conical roofs and the stripy stacks at the edges of the pic: I was planning on adding this as simple painted card cut out as that is the extent of the low relief width. G. 5 Link to post Share on other sites More sharing options...
grahame Posted March 16, 2018 Author Share Posted March 16, 2018 (edited) The tall chimney stacks are now made and primed. I'll paint the stripes on, so they have not been added as wrap arounds which would add unnecessary relief. In N/2mm these are still quite small (around 30mm tall) so this pic is quite a cruel enlargement. Each includes 12 bits of cut card and styrene: G. Edited March 16, 2018 by grahame 2 Link to post Share on other sites More sharing options...
RMweb Gold phil_sutters Posted March 16, 2018 RMweb Gold Share Posted March 16, 2018 (edited) I was was wondering where I had seen stripey chimneys before and seemed to remember some London County Council Estates had them. I had a look around online and came across this example which also has round corner towers, albeit without the conical caps.. http://www.alamy.com/stock-photo-boundary-street-estate-london-england-4960219.html Edited March 16, 2018 by phil_sutters 1 Link to post Share on other sites More sharing options...
grahame Posted March 16, 2018 Author Share Posted March 16, 2018 I was was wondering where I had seen stripey chimneys before and seemed to remember some London County Council Estates had them. I had a look around online and came across this example which also has round corner towers, albeit without the conical caps.. That's a striking (and stripey) building. It'd make an impressive model. The stripes are repeated on the towers and walls. I do wonder about the door in the central gable end - it seems to lead to over the edge of a small roof without railings. I have seen other examples of tall stripey stacks - just it tends to be from trains on South London viaducts. G Link to post Share on other sites More sharing options...
RMweb Premium Kylestrome Posted March 16, 2018 RMweb Premium Share Posted March 16, 2018 (edited) The main consideration is how to fix them in place - do I make them shaped to fit and attach to the conical roof (probably very tricky) or do I cut holes in the roof for them to sit in (also tricky). I'll make them first and then decide: You've probably already decided how you are going to do this, but I would say that cutting the cones to fit the chimney stacks is a much easier option. Cutting off material a bit at a time and finishing with a sanding block, assuming you haven't yet fixed the 'cones' in place? David PS Cutting the roof to fit the cones was much trickier, surely!? Edited March 16, 2018 by Kylestrome Link to post Share on other sites More sharing options...
grahame Posted March 16, 2018 Author Share Posted March 16, 2018 Yep, I've cut the cones to accommodate the stacks. And here they are, not glued but just resting in place to allow some fettling to ensure they are fitted absolutely vertical and upright. There's nothing worse than wonky chimney stacks and god knows I've already got enough of them: But that's enough modelling for this morning now - as soon as I've finished this pot of tea I'm going to have a bath (sounds like I'm on the Golgafrincham's B ark). G. 11 1 Link to post Share on other sites More sharing options...
grahame Posted March 16, 2018 Author Share Posted March 16, 2018 I've now got some basic blocks of colour on including the stripes which were done freehand. There's still details to be picked out. I'm currently umming and ahhing about whether to add the red bricks around the windows by painting. I've a feeling it might be a little too garish but then much will probably be covered by weathering. Being at the back of the layout and not trying to be an exact replica it doesn't matter too much (so long as it captures the overall look of the actual building) : G. 13 Link to post Share on other sites More sharing options...
grahame Posted March 17, 2018 Author Share Posted March 17, 2018 Some windows in now and assemblies glued in place. But details like the prominent rainwater down pipes to make and add as well as finish the windows: G. 7 Link to post Share on other sites More sharing options...
grahame Posted March 17, 2018 Author Share Posted March 17, 2018 And now with the final few windows in place. A little tricky and only just reachable with one finger inside the tower (I had checked) with the pre-glued window carefully balanced on the finger to press in to place: G. 10 Link to post Share on other sites More sharing options...
Job's Modelling Posted March 18, 2018 Share Posted March 18, 2018 The result is amazing. 1 Link to post Share on other sites More sharing options...
GreenBR Posted March 18, 2018 Share Posted March 18, 2018 (edited) Hello, You have done it again excellent. Regards Edited March 18, 2018 by GreenBR 1 Link to post Share on other sites More sharing options...
Branwell Posted March 18, 2018 Share Posted March 18, 2018 Lovely work, Grahame. Link to post Share on other sites More sharing options...
KNP Posted March 18, 2018 Share Posted March 18, 2018 And now with the final few windows in place. A little tricky and only just reachable with one finger inside the tower (I had checked) with the pre-glued window carefully balanced on the finger to press in to place: DSC_4986.JPG G. Very effect. The colours look exactly right.. Link to post Share on other sites More sharing options...
grahame Posted March 26, 2018 Author Share Posted March 26, 2018 I thought for the next construction project I'd attempt a building site (probably a bomb site clearance) diorama. It did exist in real life in Tooley Street and appears to have been left derelict up until the 70s, although I've not been able to find any decent reference photos. Nonetheless it should be easy enough to find pics of other similar sites to get inspiration and details from. To get started I've cut a base from mount board that includes the street corner pavement and the back garden from the property next door (that I've already made the basic shell for) : Next to undertake some research. G 14 Link to post Share on other sites More sharing options...
grahame Posted March 26, 2018 Author Share Posted March 26, 2018 It's quite therapeutic cutting little bits of plasticard and cardboard and sticking them in place. Being near the back of the layout and behind other buildings there is less need for high levels of detail and the surfaces facing away towards the back-scene don't need excessive details added and fancy paintwork. G. 7 Link to post Share on other sites More sharing options...
grahame Posted March 26, 2018 Author Share Posted March 26, 2018 I've knocked up some rough old site fencing from Redutex corrugated rusted sheet and styrene strip this afternoon, but I'm not sure about it - so it's not glued in place: G. 10 Link to post Share on other sites More sharing options...
grahame Posted March 26, 2018 Author Share Posted March 26, 2018 And a final little bit of detail for this evening . . . . G. 15 Link to post Share on other sites More sharing options...
grahame Posted March 27, 2018 Author Share Posted March 27, 2018 I've got some basic ground cover and colour on now, so the next step will be making and adding piles of bricks, rubble and planks/beams of wood plus all the other fun to model details: It's certainly a lot different to making complete buildings but does at least take the place of one. And should make it easier to see the buildings on the other side of the main street. G. 8 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now