34theletterbetweenB&D Posted February 27, 2020 Share Posted February 27, 2020 On 25/02/2020 at 18:33, scottishsteam said: I managed to pick one of these up in Oxford's "factory reject bin" on Sunday at Model Rail Scotland for £20. It was advertised as a non-runner with split gears (which I have now fixed), but the chimney is also not sitting correctly on the smokebox. I am a recent returnee to modelling with limited skills, can anybody suggest what might be the best way to remove the chimney so that I can reattach it in the correct position? I can live with it (especially for £20!) if it is a very difficult task. You lucky man! The chimney simply isn't properly seated. Try pulling it out. Then investigate why the locating spigot doesn't go down the hole in the smoke box until fully seated. It will likely be useful to take the body off the mechanism to attend to the fitting. 1 Link to post Share on other sites More sharing options...
scottishsteam Posted February 27, 2020 Share Posted February 27, 2020 12 hours ago, 34theletterbetweenB&D said: You lucky man! The chimney simply isn't properly seated. Try pulling it out. Then investigate why the locating spigot doesn't go down the hole in the smoke box until fully seated. It will likely be useful to take the body off the mechanism to attend to the fitting. Many thanks; ended up prying off gently. One spigot had snapped, so both cut flush and chimney glued back on. Not perfect but for the price paid I can't grumble! 9 Link to post Share on other sites More sharing options...
Andrew Thorpe Posted February 28, 2020 Share Posted February 28, 2020 You paid £20 for her? Oh well done! They are a great model aren't they? Runs beautifully too! Good effective haulers as well. 2 1 Link to post Share on other sites More sharing options...
Norton Wood Posted March 24, 2020 Share Posted March 24, 2020 Been a while since I've been on this page. However I've been creating the perfect scene for the N7 & Quints on my layout, Mile End Park has been progressing well ( Which you can follow on my blog ) Just need to look into getting some LNER 52'6 stock now. 5 Link to post Share on other sites More sharing options...
RMweb Premium Downer Posted March 29, 2020 RMweb Premium Share Posted March 29, 2020 I have to say it. I’ve tried not to, but I just have to. The wait for the sound-equipped BR N7 seems bloody endless. There, I feel better now. 2 1 1 Link to post Share on other sites More sharing options...
paul 27 Posted March 31, 2020 Share Posted March 31, 2020 (edited) If not mentioned before has this a 5 or 3 pole motor any more information on these are they quiet who makes these for Oxford. Edited March 31, 2020 by paul 27 1 Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted March 31, 2020 Share Posted March 31, 2020 Oxford have their own manufacturing facility by their account. The motor is a very smooth running sealed can, reputedly a coreless design and of unknown pole count. My two examples to date had a slight amount of gear noise out of the box, an hour of running saw the mechanism effectively quieted up to a scale 60mph as the loudest sound is the wheels on the rails. There was a slight whine at maximum speed, way faster than the real thing would move. Good traction as the model is heavy for its size, will pull any realistic load you care to hand on the hook. The weakest aspect arguably the less than elegant mounting of the couplings, the front coupling in particular protruding well forward. 2 3 Link to post Share on other sites More sharing options...
Unit basher Posted May 9, 2020 Share Posted May 9, 2020 It's been a while since anyone posted on the N7 page. Has anyone purchased a sound fitted model & what is it like? I fancy one of these & might go the extra for a sound fitted one. I usually look on YouTube to see if I can find a video of a factory fitted model so I can decided if it is worth the extra spend. I have looked but the only ones I can see are aftermarket fitted models. They do look a very fine model & its certainly something i am thinking of adding to my collection. 1 1 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted May 14, 2020 RMweb Premium Share Posted May 14, 2020 Very pleased with my first N7, and thought I'd like another. But with no sign of the announced second BR version arriving I thought I'd buy another of 69612 and renumber it. I had a few other modifications in mind, one being to change the LNE 'flower pot' chimney to the original GE type; for this, I've got a white metal chimney from an old Wills kit which would suit. So I was surprised on looking at the new arrival to find that it already had a GE chimney! Not quite believing my eyes, I looked again at the first one - sure enough, LNE 'flower pot' chimney, albeit possibly on the tall side? The picture below shows the two together and hopefully you can see the two types of chimney; the new arrival is in front: From the new one, I've already taken off the superfluous condensing gear operating lever, and the reversing lever on this side - the model has them on both sides but it only needs one, on the driver's side. I've got a picture of the real 69612 taken in the 1950s with a GE type chimney, so I'll leave the new one as it is and think of a different number for my original model. 6 Link to post Share on other sites More sharing options...
Opelsi Posted May 15, 2020 Share Posted May 15, 2020 13 hours ago, 31A said: Very pleased with my first N7, and thought I'd like another. But with no sign of the announced second BR version arriving I thought I'd buy another of 69612 and renumber it. I had a few other modifications in mind, one being to change the LNE 'flower pot' chimney to the original GE type; for this, I've got a white metal chimney from an old Wills kit which would suit. So I was surprised on looking at the new arrival to find that it already had a GE chimney! Not quite believing my eyes, I looked again at the first one - sure enough, LNE 'flower pot' chimney, albeit possibly on the tall side? The picture below shows the two together and hopefully you can see the two types of chimney; the new arrival is in front: From the new one, I've already taken off the superfluous condensing gear operating lever, and the reversing lever on this side - the model has them on both sides but it only needs one, on the driver's side. I've got a picture of the real 69612 taken in the 1950s with a GE type chimney, so I'll leave the new one as it is and think of a different number for my original model. I would be interested to know how you get along with removal of the number on the model, wondering if Oxford numbers are as easy to remove as Bachmann's numbers from models, or otherwise how far down the 'stubborn' scale they are? Thanks (in advance) & Stay Safe! 1 1 1 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted May 15, 2020 RMweb Premium Share Posted May 15, 2020 11 hours ago, Opelsi said: I would be interested to know how you get along with removal of the number on the model, wondering if Oxford numbers are as easy to remove as Bachmann's numbers from models, or otherwise how far down the 'stubborn' scale they are? Thanks (in advance) & Stay Safe! And the answer seems to be "NO"! Neither T Cut nor acrylic paint thinner seems to touch them. I resorted to scraping with a curved knife blade which I don't like doing as I always manage to damage the surface, and this was no exception. I may have to resort to re-painting within the lining panel. Oh well, it doesn't need to be a very clean engine! 1 1 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted May 15, 2020 RMweb Premium Share Posted May 15, 2020 1 hour ago, 31A said: And the answer seems to be "NO"! Neither T Cut nor acrylic paint thinner seems to touch them. I resorted to scraping with a curved knife blade which I don't like doing as I always manage to damage the surface, and this was no exception. I may have to resort to re-painting within the lining panel. Oh well, it doesn't need to be a very clean engine! Well I finally got the numbers off the other side without using a blade, they put up a good fight though. It took about an hour whilst watching TV, scrubbing with T Cut on a cotton bud, and the point of a cocktail stick. 1 1 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted May 17, 2020 RMweb Gold Share Posted May 17, 2020 (edited) On 14/05/2020 at 19:09, 31A said: Very pleased with my first N7, and thought I'd like another. But with no sign of the announced second BR version arriving I thought I'd buy another of 69612 and renumber it. I had a few other modifications in mind, one being to change the LNE 'flower pot' chimney to the original GE type; for this, I've got a white metal chimney from an old Wills kit which would suit. So I was surprised on looking at the new arrival to find that it already had a GE chimney! Not quite believing my eyes, I looked again at the first one - sure enough, LNE 'flower pot' chimney, albeit possibly on the tall side? The picture below shows the two together and hopefully you can see the two types of chimney; the new arrival is in front: From the new one, I've already taken off the superfluous condensing gear operating lever, and the reversing lever on this side - the model has them on both sides but it only needs one, on the driver's side. I've got a picture of the real 69612 taken in the 1950s with a GE type chimney, so I'll leave the new one as it is and think of a different number for my original model. Thanks 31A for this. I've removed the condensing gear lever as you have. Can you confirm it is the reversing lever on the same side which needs removing. Like you I'm really pleased with my N7. So far I've cosmetically tweaked a few areas on the model and shortened the NEM pockets adding Bachmann short couplings. This has enhanced the appearance dramatically. I'll do a blog entry shortly. I'm looking for a 31A shedded example and looking at BR Database it looks as if 69617 was allocated to Cambridge in February 1957. Looks like I'm in for a wrestle removing those Oxford tampo printed numbers. Thanks once again. Mark Edited May 17, 2020 by 46444 2 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted May 17, 2020 RMweb Premium Share Posted May 17, 2020 13 minutes ago, 46444 said: Thanks 31A for this. I've removed the condensing gear lever as you have. Can you confirm it is the reversing lever on the same side which needs removing. Like you I'm really pleased with my N7. So far I've tweaked a few areas on the model and shortened the NEM pockets adding Bachmann short couplings. This has enhanced the appearance dramatically. I'll do a blog entry shortly. I'm looking for a 31A shedded example and looking at BR Database it looks as if 69617 was allocated to Cambridge in February 1957. Looks like I'm in for a wrestle removing those Oxford tampo printed numbers. Thanks once again. Mark Yes, it is the reversing lever on the same side as the condensing gear lever which needs taking off these particular N7s, i.e. the side visible in my photo above, as they were right hand drive - you can see the reversing wheel inside the cab, on the driver's side. Yes I am really pleased with mine; the one I bought first has been in regular use since I bought it in October, and has always worked very well. There's some really nice detailing, e.g. the Westinghouse pump and pipework, so I can forgive it a few shortcomings! The N7s were a class of numerous detail differences and I think the BR version of the model best represents the 69612-69621 batch, so 69617 would be a good 'un. I'm looking for pictures of 69618 myself as it was a GN section loco for much of the BR period. 1 1 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted May 18, 2020 RMweb Gold Share Posted May 18, 2020 11 hours ago, 31A said: Yes, it is the reversing lever on the same side as the condensing gear lever which needs taking off these particular N7s, i.e. the side visible in my photo above, as they were right hand drive - you can see the reversing wheel inside the cab, on the driver's side. Yes I am really pleased with mine; the one I bought first has been in regular use since I bought it in October, and has always worked very well. There's some really nice detailing, e.g. the Westinghouse pump and pipework, so I can forgive it a few shortcomings! The N7s were a class of numerous detail differences and I think the BR version of the model best represents the 69612-69621 batch, so 69617 would be a good 'un. I'm looking for pictures of 69618 myself as it was a GN section loco for much of the BR period. Thanks once more 31A. Offending reversing lever now removed. I'm glad I found some N7/4' s allocated to Cambridge. Certainly makes life easier. I've only found one photo so far of 69617. Look forwards to seeing your take on 69618 eventually. Cheers, Mark 1 1 Link to post Share on other sites More sharing options...
stewartingram Posted May 18, 2020 Share Posted May 18, 2020 Try looking for photos on the Saffron Walden branch? I believe their main reason at 31A was for that line. Stewart 1 Link to post Share on other sites More sharing options...
RMweb Premium Colin Posted May 19, 2020 RMweb Premium Share Posted May 19, 2020 According to the Oakwood publication the 3 push-pull N7s that worked the Saffron Walden branch between 1956 and ‘58 when it was dieselised were 69651, 69690 and 69692. 69720 also gets a mention, being the loco used on initial trials on the line. There are some pictures of N7s in the book, let me know if you’d like me to take a look for anything in particular. Hope this might be of some use! 1 1 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted May 19, 2020 RMweb Gold Share Posted May 19, 2020 5 hours ago, Colin said: According to the Oakwood publication the 3 push-pull N7s that worked the Saffron Walden branch between 1956 and ‘58 when it was dieselised were 69651, 69690 and 69692. 69720 also gets a mention, being the loco used on initial trials on the line. There are some pictures of N7s in the book, let me know if you’d like me to take a look for anything in particular. Hope this might be of some use! Thanks Colin. That's a very kind offer. Out of interest what is the title of the Saffron Waldron line book you have? Cheers, Mark 1 Link to post Share on other sites More sharing options...
RMweb Premium Colin Posted May 19, 2020 RMweb Premium Share Posted May 19, 2020 Hi Mark The book is just called “The Saffron Walden Branch”, author is Peter Paye. Price is £18.95, I bought mine off a stall at a local exhibition. Colin 1 1 Link to post Share on other sites More sharing options...
NXEA! Posted May 20, 2020 Share Posted May 20, 2020 Following on from Unit basher's post, does anyone have a factory sound fitted version they can take a video of? The GER sound version appears to have sold relatively well so people must have them, but no sign of them on any forums etc. 1 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted May 28, 2020 RMweb Gold Share Posted May 28, 2020 With a few days off I've started to attack my N7. Like 31A mentioned previously the numbers take some elbow grease but perseverance and T-Cut applied with cotton buds did the trick. It has also left a suitable finish to apply the new numbers. I'm going for 69620 which was sheded at Cambridge in the mid-50's. I'll do a blog entry over the next few days but a few tweaks have certainly lifted this model to another level. I've also ordered a sheet of smokebox number plates from Pacific Models. See 4BRE20: http://www.pacificmodels.co.uk/smokebox-numberplates/4mm/br-eastern-region More soon. Cheers, Mark 2 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted June 10, 2020 RMweb Gold Share Posted June 10, 2020 Apologies for the delay in posting. Here is my renumbered and detailed Oxford N7 finished as 69620 of Cambridge 31A in the mid-50's. I'll do a blog entry in the next few days to highlight what work I have done. With a few tweaks the appearance of this lovely model is enhanced. The Pacific Models numberplate for reference. Excellent service and a great product. Well recommended. Cheers, Mark 8 1 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted June 10, 2020 RMweb Premium Share Posted June 10, 2020 That's very neatly done, Mark! How did you do the shed plate? 1 1 Link to post Share on other sites More sharing options...
RMweb Gold 46444 Posted June 10, 2020 RMweb Gold Share Posted June 10, 2020 (edited) 32 minutes ago, 31A said: That's very neatly done, Mark! How did you do the shed plate? I removed the printed factory one with T-Cut and replaced it with a Fox Transfer sealed with Johnson's Kleer before sealing with Vallejo satin varnish applied by airbrush. Hope that helps. Cheers, Mark Edited June 10, 2020 by 46444 1 Link to post Share on other sites More sharing options...
RMweb Premium 31A Posted June 10, 2020 RMweb Premium Share Posted June 10, 2020 Just now, 46444 said: I removed the printed factory one with T-Cut and replaced it with a Fox Transfer. Hope that helps. Cheers, Mark Thanks Mark, Fox transfers - didn't think of them! I shall have a look. 1 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now