Jump to content

Superquick Revisited


Recommended Posts

Posted (edited)

Thanks for that, BH!  There is clearly a lot of info out there about these models, makes me feel very ignorant!  At least they are still around, and even some of the earlier ones turn up from time to time:

IMG_4502.JPG.05ac3a8bcb22de9255e65065a2a5b7e5.JPG

 

Cheers,  Mike

Edited by Spotlc
typo
  • Like 4
Link to post
Share on other sites

Posted (edited)

Slowly making a New Roof

 

Most model buildings are seen from a higher viewpoint than is normal in real life, and so the roofs, chimneys and whatever are subjected to more rigourous inspection than usual!   The arrival of dowloadable texture sheets, in particular roof textures, has made it possible to greatly improve the appearance of any model, and Superquicks are no exception.

Possibly purists might object to altering the original, but I tend to think of it as an enhancing rather than degrading the finished model, much like curtains at the windows, or downpipes from the gutters.  So here is some progress on a new roof for B25:

IMG_4508.JPG.7b698e6fc105060b467032d8177cd332.JPG

 

The core is made from extruded polystyrene flooring insulation, (made from three pieces, because the roof pitch is less than 45°, and since no bandsaw will tilt to more than a few degrees beyond 45°, the angle must be set from a vertical face) Once glued and set, the end pitches were cut on a mitre saw, and the surfaces coverered with 0.35mm card to which Scalescenes tiling guides were glued.

 

The tiles are printed (here at 75%, like the guides) onto self-adhesive label paper and cut into strips which are then stuck on.  I cannot over emphasise how much easier this is than using glue sticks, spray adhesive or liquid glue!  You just invert each strip and lift the backing paper with the scalpel; some limited re-positioning is possible.

 

A hipped roof is more demanding to make than a gable roof, but quite entertaining to do, if you have the time!

 

Cheers,   Mike

 

Edited by Spotlc
  • Like 5
  • Craftsmanship/clever 2
Link to post
Share on other sites

  • 2 weeks later...
Posted (edited)

Nearly There!

 

This restoration proved to be more effort than I thought at first.  The porch was beyond repair, the chimneys were missing entirely, and the roof had been badly damaged, so  I'm afraid this is more of a pastiche than a restoration of the original.  It's also become the Borough Engineer's offices instead of a police station.

 

IMG_4512.JPG.9e8735b33d95937b6013d9e8fe06e8f1.JPG

I remade the porch from 2mmMDF, with the little roof done with Scalecenes slates like the main roof shown earlier, and the chimney stacks are  from wood with turned brass pots. It was obvious that the original stacks were as wide as the flat part of the roof and I thought that just two pots looked a bit meagre, so they got three each!

 

Otherwise, it's more or less true to the original as to proportions, glazing and material appearance. I did have few sheets of Superquick yellow brick for the chimney stacks and porch sides, but it doesn't match  - I imagine the original has faded a bit with time.  There are still the downpipes to do, and I'm sure the little annexe would have had a fire of some sort, so a stovepipe chimney will appear there in due course!

 

IMG_4511.JPG.82967caa8c347aa01fff23999b8d4edc.JPG

The boss's Riley Kestrel is parked outside, a fairly accurate model by Oxford Models, for which I have more than the usual affection, for the following reason.  The registration number of the model Riley is DLA 404, a number issued by London County Council in 1936, and I know this because for two blissful years in the early 1960's, I owned and drove a 1936 Lagonda Rapier, whose reg. number was DLA 121, so the rose tinted specs come out whenever I notice the Riley!

 

Sorry about the diversion!  I've greatly enjoyed bringing this building back to something like it looked originally, one of the nicest ones they ever made, great shame it was deleted!

 

Cheers,   Mike

Edited by Spotlc
  • Like 5
  • Craftsmanship/clever 1
Link to post
Share on other sites

  • RMweb Gold
3 hours ago, Spotlc said:

I did have few sheets of Superquick yellow brick for the chimney stacks and porch sides, but it doesn't match  - I imagine the original has faded a bit with time. 

 

I had a similar problem with another kit. Solved by making a photocopy of the brickwork of the original (faded) model. 

  • Like 1
  • Informative/Useful 1
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...