Jump to content
 

rogerdee

Members
 View Profile  See their activity

  • Posts

    119

  • Joined

  • Last visited

 Content Type 

Everything posted by rogerdee

  1. rogerdee
    I had the same problem cleaned the circuit board and membrane with meths but it came back after a while, ended up getting a new pad. On the bonus side bought a non working hand set really cheap replaced the pad for I think about a tenner and had it fully working for a third of the price of a new one.
  2. rogerdee
    Hi Does anyone know if any other model motor will fit in the class 22 as I cannot get one specifically for the class 22. Mine runs for a fashion but not at a constant setting going faster and slower then it stops dead and causes a short. So I am looking for a replacement. Any help Appreciated. Thx Roger
  3. rogerdee
    Ok thanks I'll give it a look
  4. rogerdee
    Both are n gauge farish 31s,the sound one is a zimo next 18 and the other a 6 pin bachma decoder
  5. rogerdee
    Hi I have 2 class 31 one with sound the other with out, can you tell me how I can get the non sound one to pull away like the sound one so I can run a consist. I have read it before some where I know I have to adjust some cv's but can you help me with which ones. I did think of copying the sound CV to the non sound but I doubt that would work. Thanks
  6. rogerdee
    Hi is it just my model or is this a power hungry model?. I have a DCC concepts power meter and when I use this locomotive the power draw seems to be twice as much as my other makes. It was fully run in and all clean and lubricated. Has anyone else noticed this or any idea how to cure it.
  7. rogerdee
    I had a similar problem with my NCE unit. I ended up splitting the feed from the booster to the track and to a separate accessories bus bar,the track feed then goes into a circuit breaker for each district of track. My has been working fine now . The point decoders work fine now and don't overloaded my system. Did you wire the auto switch correct as I remember some were sent out with the wrong wiring diagram .
  8. rogerdee
    Thanks for your suggestions, it's nice to get ideas of other user experiences.
  9. rogerdee
    All 2 aspect starter signal
  10. rogerdee
    I have six signals to install at the end on my terminus platforms and looking for a DCC decoder to operate them. Can anyone suggest something suitable at a reasonable price that would work with a NCE system which is easy to set up and use.
  11. rogerdee
    2nd 3rd radius curves and medium points
  12. rogerdee
    They are Dapol milk tankers I checked the back to backs and they seem correct with the setter,just have me stumped.
  13. rogerdee
    Hi does anyone have a good way of making these run reliable mine don't like points or even nice flat track or curves. I was thinking of taking the flange off the middle set of wheels or trying to find flangless wheels. Any ideas will be helpful.
  14. rogerdee
    They have not got any spare motors specifically for the class 22
  15. rogerdee
    Hi can anyone tell me if the motor in this locomotive is the same as a class 35 or 26 27 as I think mine is on the way out,it seems to run hot and draw a lot of current. Thanks
  16. rogerdee
    I had the same problems if the are not aligned correct they will play up. What I did was position each one and test it then screw it down while still testing,it was the only way I got the to work for me.
  17. rogerdee
    It will do this as resellecting the previous loco will start with a speed of zero so will stop the loco.what you need to do is select how many recall you want in the settings of the nice controller,it can have up to 6. Then when you start a loco you can select another then press recall to get back to the first which will then still be at the same speed setting you originally had.
  18. rogerdee
    Such bad news, she will be sadly missed by millions
  19. rogerdee
    Ok is it just me or are the wheels on this made of a different metal?. Every time I want to use it I have to clean the wheels as they seem to tarnish and loose conductivity but my 64xx I can leave for a long time and it works perfectly!!. Does anyone else have this problem.
  20. rogerdee
    If you want to use the one with out the motor as a different address you will need to program it with the motor one then take it off and program the motorised one to the number you want. The std motor decoder needs a motor to accept a address.
  21. rogerdee
    Ok thanks I'll take a look
  22. rogerdee
    Is it possibly to add a stay alive to these small 6 pin decoders,if so how?. Thx
  23. rogerdee
    Hi I have a couple of the above but they do not seem to like my Dapol locomotives, I can't get them to work smoothly and they seem to stop and start run for a little then stop and start again. The track is clean and it happens in different locomotives. Anyone else come across this ?. ( Make your MP work don't re-elect them)
  24. rogerdee
    If you look on the youchoos website they have some fitting guides which is a good start to look at. You can get a 6 pin decoder and speaker to fit in the tender.
  25. rogerdee
    Are you using can DCC accessory decoder to switch the points?. You cannot use a point CDU and switches just connected to the DCC bus.
×
×
  • Create New...