RMweb Gold Enterprisingwestern Posted May 12, 2021 RMweb Gold Share Posted May 12, 2021 3 hours ago, St Enodoc said: Thanks for that tip Mike. I've also got a Hornby EE 350hp shunter so I'll check that too. If you put sandpaper on the coupling rods, problem solved in one fell swoop! Mike. No, not that Fell. 1 1 1 Link to post Share on other sites More sharing options...
LNER4479 Posted May 12, 2021 Author Share Posted May 12, 2021 (edited) Re platform clearances, here is my hi-tec calibrated device: Note that (apart from the fact that my mob phone flatly refused to post the picture in the correct orientation DESPITE me rotating it and it appearing in the correct orientation in my gallery ... corrected now that I'm on my laptop - but what a faff) is that, as well as the platform edge dimension (19mm), I've also marked a platform wall dimension (23mm). I know that sometimes there were flat edges but most of the time there was an overhang. The point being, if you misjudged the platform edge, then it can be trimmed back quite easily; harder to move the whole platform wall. Edited May 12, 2021 by LNER4479 14 3 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted May 12, 2021 RMweb Premium Share Posted May 12, 2021 5 hours ago, LNER4479 said: Re platform clearances, here is my hi-tec calibrated device: Note that (apart from the fact that my mob phone flatly refused to post the picture in the correct orientation DESPITE me rotating it and it appearing in the correct orientation in my gallery ... corrected now that I'm on my laptop - but what a faff) is that, as well as the platform edge dimension (19mm), I've also marked a platform wall dimension (23mm). I know that sometimes there were flat edges but most of the time there was an overhang. The point being, if you misjudged the platform edge, then it can be trimmed back quite easily; harder to move the whole platform wall. We must build our platforms in a similar way. My platform walls are also set back 4mm from the edge (20+4=24 in my case though). Link to post Share on other sites More sharing options...
RMweb Premium t-b-g Posted May 13, 2021 RMweb Premium Share Posted May 13, 2021 (edited) 14 hours ago, LNER4479 said: Re platform clearances, here is my hi-tec calibrated device: Note that (apart from the fact that my mob phone flatly refused to post the picture in the correct orientation DESPITE me rotating it and it appearing in the correct orientation in my gallery ... corrected now that I'm on my laptop - but what a faff) is that, as well as the platform edge dimension (19mm), I've also marked a platform wall dimension (23mm). I know that sometimes there were flat edges but most of the time there was an overhang. The point being, if you misjudged the platform edge, then it can be trimmed back quite easily; harder to move the whole platform wall. I used to use something like that and it did the job ever so well until I built a layout with the platforms that extended from being straight onto a curve. I always regretted using my fixed clearance gauge on that as to clear the overhang on the inside or outside of the curved section, the platforms needed to be set further back from the position they needed to be on the straight. If you don't trains with lower footsteps or locos with a big overhang cause problems. So your choices are to either put the whole platform well back from the edge (leaving a huge gap on the straight bits) or to have the platform so it is not parallel to the track. Neither is ideal and I won't be having a platform like that again, although I have got a really gentle curve on the latest layout. The pencil held to the side of the carriage trick does give you an element of variable clearance widening on curves but on straight platforms, something along the lines of your simple but elegant gauge works really well. Edited May 13, 2021 by t-b-g Add photo and comment 1 Link to post Share on other sites More sharing options...
RMweb Premium t-b-g Posted May 13, 2021 RMweb Premium Share Posted May 13, 2021 (edited) Well something decided to add the photo as a second post and not in with the text! Edited May 13, 2021 by t-b-g Clarify posting 6 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted May 13, 2021 RMweb Premium Share Posted May 13, 2021 22 minutes ago, t-b-g said: I used to use something like that and it did the job ever so well until I built a layout with the platforms that extended from being straight onto a curve. I always regretted using my fixed clearance gauge on that as to clear the overhang on the inside or outside of the curved section, the platforms needed to be set further back from the position they needed to be on the straight. If you don't trains with lower footsteps or locos with a big overhang cause problems. So your choices are to either put the whole platform well back from the edge (leaving a huge gap on the straight bits) or to have the platform so it is not parallel to the track. Neither is ideal and I won't be having a platform like that again, although I have got a really gentle curve on the latest layout. The pencil held to the side of the carriage trick does give you an element of variable clearance widening on curves but on straight platforms, something along the lines of your simple but elegant gauge works really well. I do both, Tony. You can calibrate the pencil on the straight bit (by packing it out or shaving a bit off). It then works for the whole length, straight and curved. Link to post Share on other sites More sharing options...
LNER4479 Posted May 13, 2021 Author Share Posted May 13, 2021 (edited) 1 hour ago, t-b-g said: I used to use something like that and it did the job ever so well until I built a layout with the platforms that extended from being straight onto a curve. I always regretted using my fixed clearance gauge on that as to clear the overhang on the inside or outside of the curved section, the platforms needed to be set further back from the position they needed to be on the straight. If you don't trains with lower footsteps or locos with a big overhang cause problems. Just to say - absolutely! I have used the old pencil-on-the-side-of-a-vehicle trick many times in the past and not just for platforms but also for other structure clearance matters such as bridges and tunnels. I guess I'm now in the relatively privileged position of being able to build stations that are straight(!) - the days of 2 foot radius platforms are long gone (unless I'm building for someone else) I'm with Mike in trying to prevent the platform gap from being too excessive. Also - whilst on the subject - many models of the pre-'68 era have the platform tops set far too high (which in itself doesn't help with clearances). Study of pictures shows the step down to be quite considerable in some cases and hence why all older stock had steps underneath the doors. (Picture below shows one of Grantham's platforms under construction to illustrate the point) Edited May 13, 2021 by LNER4479 13 Link to post Share on other sites More sharing options...
RMweb Gold Enterprisingwestern Posted May 14, 2021 RMweb Gold Share Posted May 14, 2021 20 hours ago, t-b-g said: Well something decided to add the photo as a second post and not in with the text! Some diesels with over wide bogie sideframes didn't like that either! Mike. 1 Link to post Share on other sites More sharing options...
RMweb Premium t-b-g Posted May 14, 2021 RMweb Premium Share Posted May 14, 2021 2 hours ago, Enterprisingwestern said: Some diesels with over wide bogie sideframes didn't like that either! Mike. I remember that well. Even scale width items struggled. I often wondered whether any "punters" watching at a show ever realised that we had a succession of passenger trains running from Doncaster to Worksop but none coming back the other way. The front overhang on the GCR and GNR 4-4-2T locos used on the passenger trains was just too much for the outer platform and although they didn't catch due to the low platform, the sight of the front buffer sailing over the coping stone of the platform edge was not one I wanted anybody else to see. 2 4 Link to post Share on other sites More sharing options...
Popular Post LNER4479 Posted May 20, 2021 Author Popular Post Share Posted May 20, 2021 (edited) Standby folks ... the cavalry's arrived! Visited father for the first time in nine months and, somewhat unexpectedly, returned home with these two. Nowadays superseded by more modern offerings, Dad doesn't really do sentiment but has hung on to these two machines from an earlier era and they are now on indefinite loan to 'Hills of the North'. They're both original Hornby Dublo items. The green one (46227) I repainted some 25 odd years ago but the real star is the red 'un ... This is Dad's original Duchess purchase from when HD two-rail was first available (1959) so is over 60 years old. She was repainted by a professional model maker friend in the early 1970s - but erroneously numbered / named as 46227 'Duchess of Devonshire'! (a Polmadie loco that was never painted red in BR days). Nevertheless, that's very much as I remember her as a layout regular, almost always in charge of the 'Royal Scot', during our interminable operating sessions together. Eventually, he took matters in hand, and she not only got renumbered as one of Crewe North's regulars but also - can you spot it? - was re-wheeled and now sports 24mm Romford drivers and slightly finer bogie and tender wheels. Still a bit under scale, but a bit of an improvement. But most importantly ... After over 60 years of service, she's still as strong as an ox and game for yet more adventures! Here she is on test last night, walking away from a signal check at Shap Wells IB signal, 11 bogies in tow - no problem. The mechanism is the original HD motor from 60+ years ago - quite remarkable. So, not only will she feature in the roster for sentimental reasons but will have a real role to play, tackling the heavier trains (sleepers especially) to help out her more modern but spineless sisters! (meanwhile, the green 46227 will receive some attention, probably including a similar re-wheeling as she's still got her original HD wheels which aren't the best on Code 75!) Edited May 20, 2021 by LNER4479 48 1 Link to post Share on other sites More sharing options...
RMweb Premium Mallard60022 Posted May 21, 2021 RMweb Premium Share Posted May 21, 2021 14 hours ago, LNER4479 said: Standby folks ... the cavalry's arrived! Visited father for the first time in nine months and, somewhat unexpectedly, returned home with these two. Nowadays superseded by more modern offerings, Dad doesn't really do sentiment but has hung on to these two machines from an earlier era and they are now on indefinite loan to 'Hills of the North'. They're both original Hornby Dublo items. The green one (46227) I repainted some 25 odd years ago but the real star is the red 'un ... This is Dad's original Duchess purchase from when HD two-rail was first available (1959) so is over 60 years old. She was repainted by a professional model maker friend in the early 1970s - but erroneously numbered / named as 46227 'Duchess of Devonshire'! (a Polmadie loco that was never painted red in BR days). Nevertheless, that's very much as I remember her as a layout regular, almost always in charge of the 'Royal Scot', during our interminable operating sessions together. Eventually, he took matters in hand, and she not only got renumbered as one of Crewe North's regulars but also - can you spot it? - was re-wheeled and now sports 24mm Romford drivers and slightly finer bogie and tender wheels. Still a bit under scale, but a bit of an improvement. But most importantly ... After over 60 years of service, she's still as strong as an ox and game for yet more adventures! Here she is on test last night, walking away from a signal check at Shap Wells IB signal, 11 bogies in tow - no problem. The mechanism is the original HD motor from 60+ years ago - quite remarkable. So, not only will she feature in the roster for sentimental reasons but will have a real role to play, tackling the heavier trains (sleepers especially) to help out her more modern but spineless sisters! (meanwhile, the green 46227 will receive some attention, probably including a similar re-wheeling as she's still got her original HD wheels which aren't the best on Code 75!) There, my good buddy, is one of the main reasons for running trains on a 'Train Set' like your'n. Love it, as good a back story as on The Repair Shop which, I am embarrassed to say, I absolutely adore for the skill, enthusiasm and versatility for the Staff and overall sentiment. Lovely story Graham and I bet your Pa was over the bloody moon to see these pictures. P 2 1 1 1 Link to post Share on other sites More sharing options...
LNER4479 Posted May 21, 2021 Author Share Posted May 21, 2021 8 minutes ago, Mallard60022 said: I bet your Pa was over the bloody moon to see these pictures. He will be when I send them to him. He doesn't do internet so it'll be a case of printing off and popping in the post. I did give him a ring however to tell him of the performance trial which he appreciated! 10 Link to post Share on other sites More sharing options...
Popular Post LNER4479 Posted May 22, 2021 Author Popular Post Share Posted May 22, 2021 While we're in 'Duchess' mode ... well, just gotta be done, hasn't it? From right to left (in number order - should have put them the other way round, shouldn't I?) 6221 'Queen Elizabeth' - Previous generation Hornby. Have added some weight so it'll just about take the new Coronation Scot rake up Shap but in need of more blinging. 46224 'Princess Alexandra' - Previous generation Hornby. Suitably blinged and on the Shap roster for the Royal Scot (albeit with the BG banking!) 6225 'Duchess of Gloucester' - Previous generation Hornby. Nothing done to it but runs as the 'LMS train' on Shap 46227 'Duchess of Devonshire' - Hornby Dublo, repainted by me (as per the other night) 46228 'Duchess of Rutland' - the original Hornby Dublo loco (as per the other night) 46232 'Duchess of Montrose' - Current Hornby model. Tom D's loco just visiting. On the Shap roster 46239 'City of Chester' - Previous generation Hornby, newly arrived (Friday!). In the queue for blinging 46248 'City of Leeds' - Previous generation Hornby. Suitably blinged and on the Shap roster 46256 'Sir William A Stanier, FRS' - Current Hornby model. Nothing done to it as yet, goes to shows as Shap back-up loco Missing is 46251 'City of Nottingham', my Model Loco (DJH) build from 25 years ago - currently performing somewhere in the Aberdeen area. I also have 46238 'City of Carlisle' (of course!), a rather indifferent Wrenn performer and most of a further previous generation Hornby loco (courtesy of Barry O) also in the queue. So at least a quarter of the class to call on, in one form or another. Only about another 25 to go ... Anyhow, great excitement in the offing. As Boris now sez we can, then we've got a first Hills of the North operating session set up for tomorrow. I'll try and remember to take some photos ... 28 Link to post Share on other sites More sharing options...
RMweb Premium Barry O Posted May 23, 2021 RMweb Premium Share Posted May 23, 2021 Possibly some more duchesses may be visiting... Baz 4 Link to post Share on other sites More sharing options...
RMweb Gold Graham T Posted May 23, 2021 RMweb Gold Share Posted May 23, 2021 On 20/05/2021 at 23:40, LNER4479 said: Standby folks ... the cavalry's arrived! Visited father for the first time in nine months and, somewhat unexpectedly, returned home with these two. Nowadays superseded by more modern offerings, Dad doesn't really do sentiment but has hung on to these two machines from an earlier era and they are now on indefinite loan to 'Hills of the North'. They're both original Hornby Dublo items. The green one (46227) I repainted some 25 odd years ago but the real star is the red 'un ... This is Dad's original Duchess purchase from when HD two-rail was first available (1959) so is over 60 years old. She was repainted by a professional model maker friend in the early 1970s - but erroneously numbered / named as 46227 'Duchess of Devonshire'! (a Polmadie loco that was never painted red in BR days). Nevertheless, that's very much as I remember her as a layout regular, almost always in charge of the 'Royal Scot', during our interminable operating sessions together. Eventually, he took matters in hand, and she not only got renumbered as one of Crewe North's regulars but also - can you spot it? - was re-wheeled and now sports 24mm Romford drivers and slightly finer bogie and tender wheels. Still a bit under scale, but a bit of an improvement. But most importantly ... After over 60 years of service, she's still as strong as an ox and game for yet more adventures! Here she is on test last night, walking away from a signal check at Shap Wells IB signal, 11 bogies in tow - no problem. The mechanism is the original HD motor from 60+ years ago - quite remarkable. So, not only will she feature in the roster for sentimental reasons but will have a real role to play, tackling the heavier trains (sleepers especially) to help out her more modern but spineless sisters! (meanwhile, the green 46227 will receive some attention, probably including a similar re-wheeling as she's still got her original HD wheels which aren't the best on Code 75!) What a nice read to start the day with - thanks! 2 1 Link to post Share on other sites More sharing options...
RMweb Gold queensquare Posted May 23, 2021 RMweb Gold Share Posted May 23, 2021 I do like this thread, you get a real sense of people enjoying themselves. Jerry 2 8 1 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted May 23, 2021 RMweb Premium Share Posted May 23, 2021 1 minute ago, queensquare said: I do like this thread, you get a real sense of people enjoying themselves. Jerry Railway modelling is fun, as CJF was always keen to emphasise. 2 5 Link to post Share on other sites More sharing options...
92220 Posted May 23, 2021 Share Posted May 23, 2021 3 hours ago, Barry O said: Possibly some more duchesses may be visiting... Baz Oh yes. They certainly will! Iain 3 Link to post Share on other sites More sharing options...
RMweb Premium Barry O Posted May 23, 2021 RMweb Premium Share Posted May 23, 2021 9 hours ago, 92220 said: Oh yes. They certainly will! Iain well two more were present today I ma sure Red Leader will post an actions shot of one of them on a "lent for the day" rake of coaches. great fun was had. It also proved that we do need bell type communication between operators as the one set in operation toady helped speed the moving of trains considerably. Baz 3 2 1 Link to post Share on other sites More sharing options...
Popular Post LNER4479 Posted May 23, 2021 Author Popular Post Share Posted May 23, 2021 Well, it's certainly been a fun day today. The first proper operating session on 'Hills of the North' but - perhaps more pleasing - just great to see everyone and have some semblance of 'normality' once again. I tried to take some pictures so here goes: Craig took up position at Bog Junction and acquitted himself very well, here overseeing the passage of the Coronation Scot towards Central station. In truth, the Coro Scot is suffering the indignity of a signal check as Jonathan and Paul quickly realise that slick operation at Central station is key keeping the trains running. Tom, meanwhile, was right at home on his favoured ex-Midland Railway metals and soon managed to empty Garsdale of all trains that were waiting to leave. Barry is in charge at Shap summit. Yet another train heading towards Central ... But we did eventually see some trains heading out the other way. 71000 tackles Shap with ease with the Royal Scot New arrival 46239 'City of Chester' passes 'celebrity' sister loco 46228 'Duchess of Rutland' And another view of '228, strolling up Shap with her featherweight Perth express. And then there were some visitors. Barry's 46252 'City of Leicester' heads down the bank with a sort of sleeper train. A closer look at the loco, encountering ... what?!?!? Well I did say feel free to bring any locos you'd like to see run! 33 2 Link to post Share on other sites More sharing options...
Popular Post LNER4479 Posted May 23, 2021 Author Popular Post Share Posted May 23, 2021 (edited) After the ball was over: Garsdale seemed to have accumulated locos during the day. I'm sure there wasn't this many at the start of the day! Note the operating instructions for the block instruments. Meanwhile, Central is rather full(!). Nice selection of pacifics on shed. And just to expectation manage. After the last trains ran, the civil engineers moved in and here is Shap bank severed. The central area of the chapel will be given over to some much deserved love and attention to Grantham. There'll be periodic updates here but further meaningful development will resume again in the autumn. Edited May 23, 2021 by LNER4479 28 Link to post Share on other sites More sharing options...
LMS29 Posted May 23, 2021 Share Posted May 23, 2021 14 minutes ago, Barry O said: great fun was had. It also proved that we do need bell type communication between operators as the one set in operation toady helped speed the moving of trains considerably. Baz Agree with Baz. Great to run the railway, great to see the team again and the bells worked and were needed. Tom 1 1 1 Link to post Share on other sites More sharing options...
RMweb Premium Barry O Posted May 23, 2021 RMweb Premium Share Posted May 23, 2021 Oi! Who nicked shap??? 1 4 Link to post Share on other sites More sharing options...
RMweb Gold 5BarVT Posted May 23, 2021 RMweb Gold Share Posted May 23, 2021 22 minutes ago, Barry O said: Oi! Who nicked shap??? Shap’s still there, it’s Scout Green they’ve got. :-) Paul. 1 1 Link to post Share on other sites More sharing options...
jwealleans Posted May 23, 2021 Share Posted May 23, 2021 (edited) Not being overburdened with big red locos, I'm afraid I took the opportunity to shamelessly profit from another's labours and just try out a few things which have been in need of a test run since lockdown began. There'll be a few more once Grantham goes back up as well. The Wickham was on special offer from (I think) Kernow. It's been repainted from the yellow version and could do with lettering, if anyone knows where such might be sourced? It also needs some figures, ideally metal ones, but I expect they'll have to be HO to fit. This loco has yet to run at Ormesby as far as I recall: Bachmann ROD repainted and numbered to an example hired to the LSWR in 1919 (plates from 247). This had a stroll up the S & C and back with a coal train and then went onto shed. You can still see the gap where it was parked in Graham's picture above. Finally the Gauging test train.... DJH C1 (with Portescap). Birthday present to myself. I already have a number of these, but you can't have too many (until you get to 95). It was a bit of a rarity since lockdown, an Ebay buy at a sensible price, probably because it's missing the safety valve cover. This is only the second time I've had it out of the box but it worked as well as I'd hoped and can now receive some cosmetic attention prior to going into Grantham service. It cleared the tightest overhead section by a full 2.5mm. The other loco disgraced itself and can remain anonymous. Edited May 23, 2021 by jwealleans 16 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now