hayfield Posted October 9, 2021 Share Posted October 9, 2021 (edited) I have an etched chassis which cane in a lot I bought, the wheelbase is 23.5 x 23.5 mm and the length of the chassis is 102.5 mm Please can anyone shed any light as to what loco it may have come from. Similar wheelbase to a SR Terrier but it goes on to a longer footplate. I am guessing its industrial, though it may well be of a small tank loco from one of the companies. It could be even a small diesel loco Edited October 9, 2021 by hayfield Link to post Share on other sites More sharing options...
Gordon A Posted October 9, 2021 Share Posted October 9, 2021 A picture might have been helpful? Link to post Share on other sites More sharing options...
DCB Posted October 9, 2021 Share Posted October 9, 2021 Any chance of a picture? Longer footplate suggests it might be an outside cylinder loco, Chassis ends should indicate if its outside cylinder. Terriers were 20" stroke but the next Stroudley 0-6-0 class the E1 were 24" stroke with 7ft 3" between font and centre axles, much like GWR Saddle Tanks and Panniers. Any less than about 7ft WB with 24" stroke inside means some awkward angles for the con rods. Terriers were 6ft +6ft or 24mm + 24mm and 23ft or 92mm over buffer beams Link to post Share on other sites More sharing options...
hayfield Posted October 9, 2021 Author Share Posted October 9, 2021 Sorry I took one but failed to upload it 1 Link to post Share on other sites More sharing options...
Steamport Southport Posted October 9, 2021 Share Posted October 9, 2021 Look like old style Gibson replacement chassis. Might be worth looking in their catalogue as there might be a clue as to what they were meant for. Jason 1 Link to post Share on other sites More sharing options...
hayfield Posted October 9, 2021 Author Share Posted October 9, 2021 8 minutes ago, Steamport Southport said: Look like old style Gibson replacement chassis. Might be worth looking in their catalogue as there might be a clue as to what they were meant for. Jason Jason Thanks, I may just keep them for an 0-16.5 chassis, or incase I get hooked on industrials Link to post Share on other sites More sharing options...
Steamport Southport Posted October 9, 2021 Share Posted October 9, 2021 I'm wondering whether it might be for the K's GWR 1361 0-6-0ST. Jason 1 Link to post Share on other sites More sharing options...
DCB Posted October 9, 2021 Share Posted October 9, 2021 Full size 1361 and 1366 classes were 5ft + 6ft WB, K's might have stretched it a bit... 1 Link to post Share on other sites More sharing options...
Barclay Posted October 11, 2021 Share Posted October 11, 2021 On 09/10/2021 at 22:45, DCB said: Full size 1361 and 1366 classes were 5ft + 6ft WB, K's might have stretched it a bit... They did ! Interestingly the K's 1361 chassis I have is indeed 23.5mm + 23.5mm. The frames are featureless rectangles though. These frames look a bit too good to be K's... Link to post Share on other sites More sharing options...
hayfield Posted October 11, 2021 Author Share Posted October 11, 2021 45 minutes ago, Barclay said: They did ! Interestingly the K's 1361 chassis I have is indeed 23.5mm + 23.5mm. The frames are featureless rectangles though. These frames look a bit too good to be K's... The K's 1366 footplate is 88mm long these frames are 105.5mm long, I guess these could be cut down and reprofiled Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted October 14, 2021 RMweb Gold Share Posted October 14, 2021 Austerity 0-6-0ST? Link to post Share on other sites More sharing options...
Steamport Southport Posted October 14, 2021 Share Posted October 14, 2021 Frames are the wrong shape for an Austerity. They were sloped at each end. But looking at it, could be a Hunslet 16". Didn't someone like Centre Models make one? Jason 1 Link to post Share on other sites More sharing options...
Barclay Posted October 15, 2021 Share Posted October 15, 2021 I have only built one Centre Models kit and it wasn't that one but it had a cast white metal chassis block. Link to post Share on other sites More sharing options...
hayfield Posted October 15, 2021 Author Share Posted October 15, 2021 16 minutes ago, Barclay said: I have only built one Centre Models kit and it wasn't that one but it had a cast white metal chassis block. Someone suggested it was a set of Alan Gibson Mainframes, so if its the correct size the 16" Hunslet may be the answer. Though its about 6" out on the wheelbase The Alan Gibson list shows the following and there may be others listed under the smaller companies OVR Sharpe Stewart 0-6-0 Manning Wardle 0-6-0 ST Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted October 15, 2021 RMweb Gold Share Posted October 15, 2021 Could the frames be scratchbuilt? Link to post Share on other sites More sharing options...
hayfield Posted October 15, 2021 Author Share Posted October 15, 2021 21 minutes ago, Captain Kernow said: Could the frames be scratchbuilt? Thanks for the guess its made me look at the frames closer I have looked closer and they are not Milled , but show signs of being etched, as the pips which hold it to the fret have not been cleaned up. Has 2 holes for screw spacers at the ends, but its not a SEF chassis I have looked at an old Jedinco kit I built years ago, it has a similar set up of round end spacers which screw the frames together and over large headed axle bearings. 1 Link to post Share on other sites More sharing options...
Barclay Posted October 15, 2021 Share Posted October 15, 2021 In that case - they made a 'kit' for the L&Y rapid shunting tank, which has a wheelbase of 6' + 6'. The shape is about right too. Link to post Share on other sites More sharing options...
hayfield Posted October 15, 2021 Author Share Posted October 15, 2021 That may be a very good call, as there is a chassis for a L&Y 0-6-0 class 27/28 (from a Craftsman kit), although there is also what looks to be a Bristol Models milled brass GWR 28xx chassis Thank you 1 Link to post Share on other sites More sharing options...
hayfield Posted October 17, 2021 Author Share Posted October 17, 2021 Link to post Share on other sites More sharing options...
hayfield Posted October 17, 2021 Author Share Posted October 17, 2021 Another thought is I have just won a Milholme LSWR H16 loco kit, on close inspection the design of the etched chassis is very similar, whilst it may not have been a Milholme kit perhaps the person who designed the etched fret was the same. The gauge of the metal is much thicker than that which is more commonly used these days. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now