Danfilm007 Posted January 15 Author Share Posted January 15 21 minutes ago, simon b said: Is 8 loops going to be enough? Have a think about how many you need and design it around that number. I would think so! It seems to fit the available space quite well. My only challenge is trying to get the right hand side accessible from all directions (so far, you can go west to east, but can't reach the longest two sidings from the east to west direction, which is hurting my head to rectify!) Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 15 RMweb Gold Share Posted January 15 (edited) On 12/01/2024 at 16:55, Danfilm007 said: If I honest I think this design would work better for the space you have, loose all the stub end sidings and you can make the loops longer. Seems a more flexable design in that the loops can be accessed from either end without blocking both running lines. Edited January 16 by simon b Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 16 Author Share Posted January 16 6 minutes ago, simon b said: If I honest I think this design would work better for the space you have, loose all the stub end sidings and you can make the loops longer. Seems a more flexable design. It is simpler! The curvature on the ends means that you can't really fit many more points in, but I have lengthened them quite a bit so you can store multiple units in the main loops and a longer train or two too. Means it is all accessible from all routes too, and it could be managed on one board controller with a Megapoints 12 point controller for example!.. 2 Link to comment Share on other sites More sharing options...
RMweb Premium Chimer Posted January 16 RMweb Premium Share Posted January 16 (edited) At the risk of keeping you going round in circles 🤪, you could take a couple of stub sidings off each end of the shortest storage loop, which would give four more storage roads (for locos or two-car DMUs) at the cost of keeping the loop itself clear. Other than that, I think you've got the best FY solution in your latest iteration. Edited January 16 by Chimer 1 2 Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 16 RMweb Gold Share Posted January 16 (edited) 11 hours ago, Danfilm007 said: It is simpler! The curvature on the ends means that you can't really fit many more points in, but I have lengthened them quite a bit so you can store multiple units in the main loops and a longer train or two too. Means it is all accessible from all routes too, and it could be managed on one board controller with a Megapoints 12 point controller for example!.. If you want the upper loops longer you can use curved points to start them sooner, them as Chimer has suggested a few stub ends on the shorter lower loops. I'd loose the 3 way points if it were mine, they are expensive so I only use them if no alternative. Edited January 16 by simon b Link to comment Share on other sites More sharing options...
RMweb Premium PaulCheffus Posted January 16 RMweb Premium Share Posted January 16 Hi Be aware the measurements of buildings are usually the outside ones and the inside could be a lot shorter especially with adding insulation, etc. Cheers Paul 1 Link to comment Share on other sites More sharing options...
MichaelE Posted January 16 Share Posted January 16 I like your track plan except the tight curves (for the amount of room you have) in the upper left corner past the yard. Many times I wish I had built an around-the-room layout instead the current layout I have. I'm not about to start all over, but I do wish I had broader curves than 24". Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 16 Author Share Posted January 16 1 hour ago, PaulCheffus said: Hi Be aware the measurements of buildings are usually the outside ones and the inside could be a lot shorter especially with adding insulation, etc. Cheers Paul Thank you! I can fit a 15ft building in the space (this is all long-term!!) so even accounting for insulation and smaller interiors 14ft inside should touchwood be fine. Obviously we can take length out if needs be! 1 hour ago, MichaelE said: I like your track plan except the tight curves (for the amount of room you have) in the upper left corner past the yard. Many times I wish I had built an around-the-room layout instead the current layout I have. I'm not about to start all over, but I do wish I had broader curves than 24". I'm readjusted the top-left curves slightly so they are looser but even on the right hand side it is relatively tight (20"). It is all a compromise in one way or another - this version has fewer sidings but is 100% accessible from all sides, whereas the other one had more but not all were. I won't be running trains at super high speed either so I don't think it is "as much" a problem? 8 hours ago, Chimer said: At the risk of keeping you going round in circles 🤪, you could take a couple of stub sidings off each end of the shortest storage loop, which would give four more storage roads (for locos or two-car DMUs) at the cost of keeping the loop itself clear. Other than that, I think you've got the best FY solution in your latest iteration. I'll probably add one or two in - it's why I quite liked the more unconventional format as it meant there was a lot more space in each of the sidings but this is much less complex and I feel happier with it, length aside! Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 16 RMweb Gold Share Posted January 16 3 hours ago, Danfilm007 said: I'll probably add one or two in - it's why I quite liked the more unconventional format as it meant there was a lot more space in each of the sidings but this is much less complex and I feel happier with it, length aside! Curved points are your friend to get the maximum length from the loops, use them on the left side of the yard and you could fit a pair of stub end tracks on the righthand side. 1 Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 16 Author Share Posted January 16 1 hour ago, simon b said: Curved points are your friend to get the maximum length from the loops, use them on the left side of the yard and you could fit a pair of stub end tracks on the righthand side. I'll give it a go! Really, the fiddle yard entrance is just too tight to fit any more points or changes in - this layout gives me a few extra loops and growth opportunities on those ends! Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 23 Author Share Posted January 23 Me again! I had some thoughts the other day. There is a layout on here that I can't recall the name of but it's a Northern modern image layout with some carriage sidings outside the station, plus layouts like Bradfield Gloucester Square where there is a mix of both station and sidings. I've taken some inspiration from Stockport station, so I have added in both another through platform at the top (which I may "dead end" or put a point on the lift-out section for it) and some basic sidings and a headshunt. The station at Stockport is also a bit easier - it starts in a bit of a cutting and ends on a viaduct so it could be a slightly more practical thing to model. Finally, it gives some more storage in the scenic area. Do you think I am slightly mad to incorporate it? Link to comment Share on other sites More sharing options...
RMweb Gold The Stationmaster Posted January 23 RMweb Gold Share Posted January 23 I think a hallmark of main line 'city' stations is that they tended to have more bays than most through stations although there were eceptions. Oxford, a city, for example only had two bays - both at the north end while Reading , not a city. had two bays ar one end and three at the other end but it was a major junction on quadruple track. Similarly Slough, again not a city, wasquadruple track but not a major junction and had one bay at the east end and - until 1963 - two bays at the west end. Looking elsewhere Leicester Central, with a large island platform, had two bays at each end while Nottingham Central, with two through platforms in each direction at 4 bays at each end. But Sheffield Victoria was not as well provided for with bays as far as I recall. These are just a few examples where I know the detail but cities tended to have local trains which needed somewhere to terminate and start their journeys. 1 Link to comment Share on other sites More sharing options...
dave75 Posted January 23 Share Posted January 23 (edited) 1 hour ago, Danfilm007 said: I really liked your original idea, it seemed a very workable plan, lots of operational interest with turnbacks, shortish rakes of emu,dmu and the occasional freightliner. An upgrade to Stockport would seem to require a 9 car wcml set passing through every 10 mins. But its your railway run what you like. Sorry I quoted you but put my comments. V confusing. Edited January 23 by dave75 Typo 1 Link to comment Share on other sites More sharing options...
RMweb Gold TravisM Posted January 24 RMweb Gold Share Posted January 24 On 16/01/2024 at 00:15, Danfilm007 said: It is simpler! The curvature on the ends means that you can't really fit many more points in, but I have lengthened them quite a bit so you can store multiple units in the main loops and a longer train or two too. Means it is all accessible from all routes too, and it could be managed on one board controller with a Megapoints 12 point controller for example!.. I like this plan over your latest creation as everything flows nicely. By putting in carriage sidings, your creating more work for yourself if your running it as a one man band, or if you have others in to help run it, do you have enough space in the operating well without getting in each others way? 1 Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 24 Author Share Posted January 24 1 hour ago, TravisM said: I like this plan over your latest creation as everything flows nicely. By putting in carriage sidings, your creating more work for yourself if your running it as a one man band, or if you have others in to help run it, do you have enough space in the operating well without getting in each others way? You are right, I think I'll abandon the idea od the sidings as it seems a bit much. I think I'll steal the changing heights aspect though! 1 1 Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 24 RMweb Gold Share Posted January 24 Dan, what sort of trains are you planning to run on this? Mostly multiple units, or longer loco hauled passenger trains? 1 Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 26 Author Share Posted January 26 On 24/01/2024 at 18:16, simon b said: Dan, what sort of trains are you planning to run on this? Mostly multiple units, or longer loco hauled passenger trains? Mostly DMUs/EMUs and a couple of Loco hauled passenger stock Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 26 RMweb Gold Share Posted January 26 4 hours ago, Danfilm007 said: Mostly DMUs/EMUs and a couple of Loco hauled passenger stock I know Leicester central was mentioned a few posts ago, I wonder if something like that might better suit your stock? This is just a quick go in anyrail to give you an idea, it isnt to scale at all. 2 1 1 Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 26 Author Share Posted January 26 6 hours ago, simon b said: I know Leicester central was mentioned a few posts ago, I wonder if something like that might better suit your stock? This is just a quick go in anyrail to give you an idea, it isnt to scale at all. Interesting idea! Certainly is an interesting concept. Part of my reason for an Oxford Road style station was the variety of running but this station is more flexible in terms of reversal bays etc! 1 Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 26 RMweb Gold Share Posted January 26 (edited) 1 hour ago, Danfilm007 said: Interesting idea! Certainly is an interesting concept. Part of my reason for an Oxford Road style station was the variety of running but this station is more flexible in terms of reversal bays etc! The great thing about this plan is that you dont need the outer crossovers oxford road has, all reversals are done in the bay roads. You can have your freight and loco hauled passengers going around the circuits via the outer platforms, then bring out a multiple unit from the bays, do a few circuits and bring it into the opposite end bay platform. No need for multiple units to use the fiddle yard at all, saving space for freight trains. I've drawn it with a freight loop on each side, so you can overtake trains. The real station had more loops than that but it's up to you if you want to keep them or have none at all. Edited January 26 by simon b pic added 2 1 Link to comment Share on other sites More sharing options...
Danfilm007 Posted January 26 Author Share Posted January 26 2 minutes ago, simon b said: The great thing about this plan is that you dont need the outer crossovers oxford road has, all reversals are done in the bay roads. You can have your freight and loco hauled passengers going around the circuits via the outer platforms, then bring out a multiple unit from the bays, do a few circuits and bring it into the opposite end bay platform. No need for multiple units to use the fiddle yard at all, saving space for freight trains. I've drawn it with a freight loop on each side, so you can overtake trains. The real station had more loops than that but it's up to you if you want to keep them or have none at all. Food for thought! It does flow quite nicely. I must admit I'm a bit of a sucker for the way Oxford Road flows with its point works and tightness but it does obviously work better your way 2 Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 26 RMweb Gold Share Posted January 26 1 hour ago, Danfilm007 said: Food for thought! It does flow quite nicely. I must admit I'm a bit of a sucker for the way Oxford Road flows with its point works and tightness but it does obviously work better your way It's just another idea for you, dont feel you have to go along with any of them. It's all about designing something that you will be happy with, and suits your operating style. Some people like to play about shunting a yard, others like to watch trains run by. 2 Link to comment Share on other sites More sharing options...
RMweb Premium St Enodoc Posted January 27 RMweb Premium Share Posted January 27 17 hours ago, simon b said: I know Leicester central was mentioned a few posts ago, I wonder if something like that might better suit your stock? This is just a quick go in anyrail to give you an idea, it isnt to scale at all. The bays are quite short. If I were going this way, I'd be inclined to get enough length for a 3-car unit by shortening the "bridging" platform in the middle. Link to comment Share on other sites More sharing options...
RMweb Gold simon b Posted January 27 RMweb Gold Share Posted January 27 3 hours ago, St Enodoc said: The bays are quite short. If I were going this way, I'd be inclined to get enough length for a 3-car unit by shortening the "bridging" platform in the middle. Yep they are, it isnt to scale at all as I hit the limit of 50 track sections in free anyrail. The whole thing would need to be on a curve to fit in the 14ft length available, but the bays should ideally take a 3 car 158. 1 1 Link to comment Share on other sites More sharing options...
RobinofLoxley Posted January 27 Share Posted January 27 4 hours ago, St Enodoc said: The bays are quite short. If I were going this way, I'd be inclined to get enough length for a 3-car unit by shortening the "bridging" platform in the middle. Just remember that the bays both ends have to do that. Recently there was a thread about Darlington, here, which has a single ended bay, but fitting it into the available space. Personally i would say that proposal is too symmetrical. That might be how it is, but there arent many operating variations compared to Oxford Road. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now