Popular Post 92220 Posted March 2, 2020 Popular Post Share Posted March 2, 2020 21 minutes ago, Tony Wright said: Thanks Iain, I feel, if any apologies were necessary, they should have come from me. 46146 appeared to have been running fine on Shap, until it started to slip out of gear - chattering and jerking. Normally, I would never touch the work of anyone else unless they specifically asked me. However, as I'd already sorted out the mangled gear on a 'Duchess' and done something with the weirdest pick-ups I've ever seen on a 'Jubilee', Graham asked me to look at your 'Scot'. I did replace the bits which came adrift (because of my clumsiness!), apart from that long-gone sandbox filler, but I was unable to make it go again. You've made such a lovely job of detailing/weathering 46146 that it deserves a decent chassis (though, when you make one, will you tell me how to get the body off?). I'm afraid that failing steam-outline modern RTR chassis is no longer a phenomenon. It's much too common to be described thus. Regards, Tony. No apology needed, Tony, but thank you for repairing it as best you could. Thank you too for your kind praise of my work. I will replace the chassis at some point, endeavouring to get enough weight over the rear drivers when I do. The Hornby Scot and Patriot bodies are a workable basis for a decent model, I think, with some willingness to do some modelling. If I could paint like Geoff Haynes or Ian Rathbone, I would build more of these: Iain 19 2 5 Link to post Share on other sites More sharing options...
LNERandBR Posted March 2, 2020 Share Posted March 2, 2020 Painting is certainly my Achilles heel. I'd build far more kits if I felt I could paint them to an acceptable standard. Weathering meanwhile is far more up my street. I suppose it's one of those practice makes perfect things. 1 Link to post Share on other sites More sharing options...
Tony Wright Posted March 2, 2020 Author Share Posted March 2, 2020 Practise does make perfect, I suppose. As long as you're competent at practising what you're doing. I'm afraid, practise-wise, when it comes to painting, I'll never reach the high standards of the pros. A standard like this....... An O Gauge Precussor tank, painted by Geoff Haynes. Was there ever a more practical, yet elegant, livery for a steam loco? No matter my shortcomings in painting. I build as a sub-contrator for Geoff in exchange. All the best modellers/painters have a years-ahead waiting list! 9 3 4 Link to post Share on other sites More sharing options...
Tony Wright Posted March 2, 2020 Author Share Posted March 2, 2020 5 hours ago, 92220 said: No apology needed, Tony, but thank you for repairing it as best you could. Thank you too for your kind praise of my work. I will replace the chassis at some point, endeavouring to get enough weight over the rear drivers when I do. The Hornby Scot and Patriot bodies are a workable basis for a decent model, I think, with some willingness to do some modelling. If I could paint like Geoff Haynes or Ian Rathbone, I would build more of these: Iain Beautiful work, Iain, I suppose Geoff Haynes will be painting the 'Scot'? Just one comment. The buffers, as supplied by Comet, are too small in diameter for a 'Scot'. They suit a 'Jubilee' or a rebuilt 'Patriot', but the 'Scots' had larger-diameter buffer heads. Regards, Tony. 1 Link to post Share on other sites More sharing options...
davefrk Posted March 2, 2020 Share Posted March 2, 2020 Yes correct about the front buffers on the Scots, should be 18'' diameter. Lanarkshire Models happen to do the correct ones. http://lanarkshiremodels.com/lanarkshiremodelsandsupplieswebsite_129.htm Just saying. Cheers, dave Franks. 6 Link to post Share on other sites More sharing options...
Daniel W Posted March 2, 2020 Share Posted March 2, 2020 It was a pleasure to talk to you on Saturday, Tony. I tried the bodge you suggested using low-melt solder as filler on the wagon kit and it worked a treat! Definitely a trick worth bearing in mind for the future. 1 Link to post Share on other sites More sharing options...
Popular Post 92220 Posted March 2, 2020 Popular Post Share Posted March 2, 2020 Yes, I have some overlays to apply for the Scot buffer heads. I have to save up for Geoff to paint this. He did make a beautiful job of Sir William, seen here before adding all of the lubricators etc, which I left off for ease of painting and lining: Iain 23 4 Link to post Share on other sites More sharing options...
92220 Posted March 2, 2020 Share Posted March 2, 2020 1 hour ago, davefrk said: Yes correct about the front buffers on the Scots, should be 18'' diameter. Lanarkshire Models happen to do the correct ones. http://lanarkshiremodels.com/lanarkshiremodelsandsupplieswebsite_129.htm Just saying. Cheers, dave Franks. Mmmm, would have been easier to buy these in the beginning! I will definitely do so for any future Comet Scot builds. thanks, Iain 1 Link to post Share on other sites More sharing options...
Popular Post Jol Wilkinson Posted March 2, 2020 Popular Post Share Posted March 2, 2020 (edited) Tony, how right you are about the LNWR livery. No wonder that BR chose it for the mixed traffic locos. Here is another example, this time in 4mm and painted by Ian Rathbone (but with dust carefully applied by me). In the background is a LNWR Cauliflower 0-6-0, this time painted by an amateur and lined with waterslide transfers. Photo courtesy of Barry Norman/MRJ Although the workmanship of Geoff, Ian and other top flight painters is beyond what most of us can achieve, I find it is possible to get a good result for the the LNWR livery by using an airbrush with cellulose paint and good quality transfers. Edited March 2, 2020 by Jol Wilkinson Amended text 21 Link to post Share on other sites More sharing options...
Tony Wright Posted March 2, 2020 Author Share Posted March 2, 2020 3 hours ago, Daniel W said: It was a pleasure to talk to you on Saturday, Tony. I tried the bodge you suggested using low-melt solder as filler on the wagon kit and it worked a treat! Definitely a trick worth bearing in mind for the future. And a pleasure to talk to you as well, Daniel. I'm glad the soldering dodge worked. And, I hope my re-soldering of the brake lever meant it stayed put. Well done for tackling your first etched kit. Too many 'modellers' don't even try....... Regards, Tony. 1 Link to post Share on other sites More sharing options...
Tony Wright Posted March 2, 2020 Author Share Posted March 2, 2020 2 hours ago, Jol Wilkinson said: Tony, how right you are about the LNWR livery. No wonder that BR chose it for the mixed traffic locos. Here is another example, this time in 4mm and painted by Ian Rathbone (but with dust carefully applied by me). In the background is a LNWR Cauliflower 0-6-0, this time painted by an amateur and lined with waterslide transfers. Photo courtesy of Barry Norman/MRJ Although the workmanship of Geoff, Ian and other top flight painters is beyond what most of us can achieve, I find it is possible to get a good result for the the LNWR livery by using an airbrush with cellulose paint and good quality transfers. A beautiful locomotive, Jol, I take it, this is the same one? Regards, Tony. 9 2 Link to post Share on other sites More sharing options...
Popular Post Tony Wright Posted March 2, 2020 Author Popular Post Share Posted March 2, 2020 (edited) 2 hours ago, 92220 said: Yes, I have some overlays to apply for the Scot buffer heads. I have to save up for Geoff to paint this. He did make a beautiful job of Sir William, seen here before adding all of the lubricators etc, which I left off for ease of painting and lining: Iain It is very nice, Iain....... And Geoff also did a beautiful job of painting my DJH 'Coronation'. Here she is, entirely at home on Shap. A full report on how I built this loco will be appearing in the next issue of the Railway Modeller. She'll also be running over Shap at the York Show at Easter...... Some time ago, I also produced a 46256........ Which Ian Rathbone painted for me. It's a Hornby/Comet conversion. Hornby now does exactly the same loco, for around £175.00. I'm sure it's good, but all one needs is money to acquire it; not model-making skills at all - something the hobby is in danger of losing in the not-too-distant future if we're not careful. Regards, Tony. Edited March 2, 2020 by Tony Wright to clarify a point 19 1 Link to post Share on other sites More sharing options...
DougN Posted March 2, 2020 Share Posted March 2, 2020 As the cost of the RTR versions is constantly rising and the second hand value of the kits falling. Do you think there is a point where more people will start saying "I'll have a go at this kit building"? I believe there is a point where some (I am not suggesting all) will start looking at this thread, and others, and have a go. Painting will be the next stumbling point after soldering. I am still not there yet but I have a set procedure that is working for me. Also the materials I am using are available to me, being here in Australia, we do not get the same manufacturers of paint such as Precision or Railmatch here due to the export/ import restrictions. 4 1 Link to post Share on other sites More sharing options...
Tony Wright Posted March 2, 2020 Author Share Posted March 2, 2020 Just now, DougN said: As the cost of the RTR versions is constantly rising and the second hand value of the kits falling. Do you think there is a point where more people will start saying "I'll have a go at this kit building"? I believe there is a point where some (I am not suggesting all) will start looking at this thread, and others, and have a go. Painting will be the next stumbling point after soldering. I am still not there yet but I have a set procedure that is working for me. Also the materials I am using are available to me, being here in Australia, we do not get the same manufacturers of paint such as Precision or Railmatch here due to the export/ import restrictions. 'As the cost of the RTR versions is constantly rising and the second hand value of the kits falling. Do you think there is a point where more people will start saying "I'll have a go at this kit building"?' I certainly hope so, Doug, You might have something here....... Regards, Tony. 3 Link to post Share on other sites More sharing options...
RMweb Premium Chamby Posted March 2, 2020 RMweb Premium Share Posted March 2, 2020 43 minutes ago, DougN said: As the cost of the RTR versions is constantly rising and the second hand value of the kits falling. Do you think there is a point where more people will start saying "I'll have a go at this kit building"? I believe there is a point where some (I am not suggesting all) will start looking at this thread, and others, and have a go. Another factor will be the longevity of the products. Current specification RTR yields mighty fine models, but they are also very delicate and it is so easy to lose bits or bend stuff, even with careful handling. I do wonder how long some of them will last, how many of my RTR loco’s might eventually end up as static exhibits in the loco depot. I have come to the conclusion that there is a balance to be achieved between fine-ness and practicality, with current RTR having swung too far towards the detail. Tony has frequently commented recently about RTR products being more accurate... but this accuracy and ‘high fidelity’ does come at a cost with regards to durability with real-world handling. And fixing things is much easier if you have built it yourself in the first place! 1 8 Link to post Share on other sites More sharing options...
Tony Wright Posted March 3, 2020 Author Share Posted March 3, 2020 9 hours ago, Chamby said: Another factor will be the longevity of the products. Current specification RTR yields mighty fine models, but they are also very delicate and it is so easy to lose bits or bend stuff, even with careful handling. I do wonder how long some of them will last, how many of my RTR loco’s might eventually end up as static exhibits in the loco depot. I have come to the conclusion that there is a balance to be achieved between fine-ness and practicality, with current RTR having swung too far towards the detail. Tony has frequently commented recently about RTR products being more accurate... but this accuracy and ‘high fidelity’ does come at a cost with regards to durability with real-world handling. And fixing things is much easier if you have built it yourself in the first place! Thanks Phil, 'And fixing things is much easier if you have built it yourself in the first place!' Especially if built in metal. Then it can be soldered together! I know there are many out there (and on here) who build things in plastic - Plastikard or adaptations. Even though I'm quite happy to build simple plastic wagon kits as part of my demonstrating at shows, it's not my medium. In fact, I rather dislike it - all that static mess! Regarding longevity and reliability with regard to modern RTR, I don't think so. I see so many models/pictures of models showing many more-recent OO Hornby/Bachmann/Heljan/etc steam-outline locos missing the likes of front steps, vacuum pipes, 'proper' couplings and cylinder drain cocks. Time was when such 'fripperies' were never provided RTR, and even now they have to fixed on by the purchaser (and, have you seen the mess some make of this simple act?). Made in metal, and soldered in place, such things don't come adrift. But then, the soldering has to be done properly! As for failing/splitting/crumbling modern RTR drives; it's far too common in my experience. Regards, Tony. 1 Link to post Share on other sites More sharing options...
Headstock Posted March 3, 2020 Share Posted March 3, 2020 I don't consider RTR to be intrinsically more accurate than kits. There are good kits, not so good kits and bad kits. The same can also be said of RTR. A detailed perusal of the average RTR manufactures catalogue, would Surprise a lot of people as to just how high the percentage of inaccurate RTR models they contain. As for detail, it doesn't have to be flimsy. This is very much a cost choice by manufactures and laziness on the part of modellers. 2 Link to post Share on other sites More sharing options...
ScRSG Posted March 3, 2020 Share Posted March 3, 2020 11 hours ago, Tony Wright said: 'As the cost of the RTR versions is constantly rising and the second hand value of the kits falling. Do you think there is a point where more people will start saying "I'll have a go at this kit building"?' Don't know if I agree totally here regarding kit prices falling, if ebay is anything to go by. I have been following several kits recently and the prices seem to be getting higher and higher. There still seems to be a high demand for kits. 3 1 Link to post Share on other sites More sharing options...
grahame Posted March 3, 2020 Share Posted March 3, 2020 56 minutes ago, Headstock said: As for detail, it doesn't have to be flimsy. This is very much a cost choice by manufactures and laziness on the part of modellers. Yep, and damage or broken off bits are often caused through clumsiness, maltreatment and bad handling by owners. If people want to treat models roughly there are plenty of robust children's toys, some made from wood, that can purchased and played with. ;-) 2 Link to post Share on other sites More sharing options...
Tony Wright Posted March 3, 2020 Author Share Posted March 3, 2020 1 hour ago, ScRSG said: Don't know if I agree totally here regarding kit prices falling, if ebay is anything to go by. I have been following several kits recently and the prices seem to be getting higher and higher. There still seems to be a high demand for kits. I'm inclined to agree, Even though I was quoting Doug's statement. Regards, Tony. P.S. Good to see you again in Glasgow. 1 Link to post Share on other sites More sharing options...
Jol Wilkinson Posted March 3, 2020 Share Posted March 3, 2020 14 hours ago, Tony Wright said: A beautiful locomotive, Jol, I take it, this is the same one? Regards, Tony. Yes it is, from the super photos you kindly took when London Road appeared at York MRS in 2018. I used the Barry Norman photo as it was more close up to show Ian Rathbone's painting and lining. Your photos capture the loco and train excellently in the overall context of the layout. 3 1 Link to post Share on other sites More sharing options...
Headstock Posted March 3, 2020 Share Posted March 3, 2020 1 hour ago, grahame said: Yep, and damage or broken off bits are often caused through clumsiness, maltreatment and bad handling by owners. If people want to treat models roughly there are plenty of robust children's toys, some made from wood, that can purchased and played with. ;-) Or a football, you can kick that until your hearts content. 1 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted March 3, 2020 RMweb Premium Share Posted March 3, 2020 2 hours ago, ScRSG said: Don't know if I agree totally here regarding kit prices falling, if ebay is anything to go by. I have been following several kits recently and the prices seem to be getting higher and higher. There still seems to be a high demand for kits. I wish the prices of Slaters Toplights would fall a bit... 1 Link to post Share on other sites More sharing options...
Denbridge Posted March 3, 2020 Share Posted March 3, 2020 13 minutes ago, St Enodoc said: I wish the prices of Slaters Toplights would fall a bit... They should, once Slaters get round to bringing them back to market. 1 Link to post Share on other sites More sharing options...
RMweb Premium Steven B Posted March 3, 2020 RMweb Premium Share Posted March 3, 2020 Is buying RTR realy that different to building a kit that someone else has designed and then paying someone else to paint it? (regardless of if the payment is cash or in exhange for building a kit for your painter?) Without wanting to sound rude, there are many posts on this thread that appear to look-down upon those who buy RTR models. Surely getting someone else to build or paint a kit is only one step removed? A person might be an expert in producing scenary but is happy with RTR models. Does this make them any less of a "modeller"? Steven B. 3 5 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now