A Distraction - Tilt Wagon
In my previous post, I made the self-fulfilling prophesy that I would be distracted by the forum thread on GWR standard gauge 'tilt' wagons, started by drduncan. Initially there was some discussion as to whether the photo shown was, in fact, of a Broad Gauge wagon but the dimensions (especially the height) seemed sufficiently different to indicate that the vehicle under discussion was indeed Standard Gauge.
Something 'clicked' for me and I decided that I had to add one to my stock, so I began to prepare simple drawings by scaling the photograph, using the assumption that the wheelbase was 9' 9", as in the BG versions. The result, produced in Autosketch by tracing over the photograph, looked like this:
Because the original was of metal construction, I wanted to do the same with my model but I also decided to try a new way of marking out my 10 thou (0.25 mm) brass sheet, making use of my Silhouette Portrait cutter. Previously, my method has been to cut out sections of drawings on paper and stick these to brass sheet, using a glue pen. I then simply cut out the parts by following the printed lines with jewellers' snips.
This time, I decided to use a diamond scriber in the pen holder of the Silhouette cutter, to mark out the outlines of the components directly onto brass sheet. As well as the outlines, this method also enabled me to scribe details, such as planking and guidelines for attaching surface details.
In addition, I realised that if I drew the outline of my rectangular brass sheet on a sheet of paper and also added the Silhouette registration marks, then I could scribe both sides of the brass sheet, in registration. To do this, I lightly taped the brass to the paper, aligned with my outline drawing, and then scribed the detail. I then turned the brass over and scribed the other side with the appropriate designs - remembering to flip the Silhouette image to correspond with the way I turned the sheet over.
Scribing Brass Sheet with a Silhouette Cutter
After cutting out the individual components, I assembled the basic shape of the Tilt Wagon, as shown below. I have a set of socket spanners in a wide range of diameters which provide useful 'jigs' for setting the curvature of the end bonnets. I used super-glue to fix the bonnets inside the folded wagon sides and then inserted the curved ends into the bonnets. I prefer using super-glue to solder where there are lots of different small parts to be fitted together, as it avoids earlier joints melting while new ones are being made. Inevitably, some glue extrudes from the sides of the joints and I use a small stainless steel chisel, intended for wax carving, to remove this excess while it is still at a 'cheesy' consistency.
A prominent feature of the prototype is the extensive use of rivets! I decided to 'cheat' and use the rivet strips that are currently available from 'Mainly Trains'. I realise that this means the rivet heads are on a raised 'plinth' but I find that the near-perfect alignment is preferable, at normal viewing distances, to my attempts at embossing even lines! Additional details are the angle-iron stiffeners along the tops of the sides and on the side doors (1mm brass angle), and the wooden cross-bar at the top of the doors (plasticard). I still have to add the rails above the sides and between the tops of the end bonnets.
There remains the little matter of a chassis! I find that the GWR W-irons from MJT are still listed as "temporarily out of stock", as they have been all year! In addition, I see that 'Mainly Trains' have a notice on their website that "After 35 Years of trading we are beginning the process of winding down." It looks rather ominous for the future supply of many very useful detailing components!
Perhaps I shall have to turn to completely scratch-building the chassis as well....
In the meantime, my 'work in progress' looks like this, making an interesting comparison with a round-ended 3-planker from David Geen.
Mike
Edited by MikeOxon
Restore images
- 9
- 1
14 Comments
Recommended Comments
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now