Thebodger Posted September 24, 2020 Share Posted September 24, 2020 I've loved railway modelling for some time but always fell at the first hurdle of scenic modelling when applied ballast ruined my points and the railway ceased to function... However the discovery, known already I'm sure of everyone on the forum that seep point motors with switches solved my electrical problems was a revelation! Have now motorised all five of my points carefully testing as I went along, all correct according to the multimeter however after 10 minutes testing one of my motors has developed an intermittent fault with the polarity switch. Extensive testing with the multimeter shows that both wires entering the motor are ok suggesting the problem is in the motor, I have removed the motor from the board where all appeared fine as did it after reinstalling for 10 or so cycles after which the intermittent fault returned. Can anyone suggest why this may be and suggest a solution to my problem. Or are seep motors simply that unreliable? Many thanks Bodger Link to post Share on other sites More sharing options...
RMweb Gold ikcdab Posted September 24, 2020 RMweb Gold Share Posted September 24, 2020 If the polarity switch is the "slidey" spring thing, then yes, they are not reliable. You might find a bit of cleaning up of the conracts works, but the fact that it is all in the open air is a failing. Far better to have an enclosed switch or a relay, Ian Link to post Share on other sites More sharing options...
Michael Hodgson Posted September 24, 2020 Share Posted September 24, 2020 Not the best switches around. They aren't worth the extra over the version that doesn't have a switch. It's why some people prefer to attach microswitches or use relays etc. Having said that you've already got them and you want to use the switches. The springy moving contact strip might benefit from tweaking slightly to give greater pressure. Link to post Share on other sites More sharing options...
RMweb Gold Dagworth Posted September 24, 2020 RMweb Gold Share Posted September 24, 2020 Make sure that the motor is absolutely central under the point, otherwise the switch only gets part way in its travel. Andi 3 Link to post Share on other sites More sharing options...
RMweb Premium kevinlms Posted September 24, 2020 RMweb Premium Share Posted September 24, 2020 5 minutes ago, Dagworth said: Make sure that the motor is absolutely central under the point, otherwise the switch only gets part way in its travel. Andi Which means, 100% alignment in both directions. Otherwise it will never work reliably. 3 Link to post Share on other sites More sharing options...
stewartingram Posted September 25, 2020 Share Posted September 25, 2020 And the contacts of the switch are actually the tinned pcb track. One of the worst materials for oxidisation = loss of conductivity. Throw the switches away, add a microswitch. 1 Link to post Share on other sites More sharing options...
RMweb Premium Michael Edge Posted September 25, 2020 RMweb Premium Share Posted September 25, 2020 It's not a very good switch but electrolube on the contacts will improve it a lot - tweaking it will probably make it worse though. Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted September 25, 2020 RMweb Gold Share Posted September 25, 2020 (edited) I have found that performance definitely deteriorates over time even with cleaning and I have replaced Seeps on 2 of my exhibition layouts... Edited September 25, 2020 by Gilbert Link to post Share on other sites More sharing options...
Thebodger Posted September 25, 2020 Author Share Posted September 25, 2020 Well this is disappointing, i hoped unreliable meant weeks or months before failing not minutes can anyone recommend an alternative system that wont break the bank? Link to post Share on other sites More sharing options...
smokebox Posted September 25, 2020 Share Posted September 25, 2020 18 minutes ago, Thebodger said: Well this is disappointing, i hoped unreliable meant weeks or months before failing not minutes can anyone recommend an alternative system that wont break the bank? Try repositioning the point motor very, very slightly left or right of the rails to (hopefully) allow the moving contact of the switch, (the washer) to make a better contact with the fixed contacts (the PCB tracks). Not guaranteed to work but worth trying 1 Link to post Share on other sites More sharing options...
MartynJPearson Posted September 25, 2020 Share Posted September 25, 2020 I've used Seeps for years without any more than a few minor problems so don't give up! Alignment is key, so if they were working and stopped, it might be worth checking that they are still in position. It's quite a jolt when the solenoid activates so if it's not firmly in place it may move - and it doesn't have to move far to stop the contact. Where I have had problems, a squirt of switch cleaner followed by changing the points half a dozen times seems to do the trick. 1 Link to post Share on other sites More sharing options...
Free At Last Posted September 25, 2020 Share Posted September 25, 2020 I find slotting the two fixing holes allows a bit of play to set the switch alignment up. Link to post Share on other sites More sharing options...
bike2steam Posted September 25, 2020 Share Posted September 25, 2020 It's not rocket science getting them set up square, and central, and as mentioned above, use micro-switches for polarity change. Used them for years, no problem. 1 Link to post Share on other sites More sharing options...
ejstubbs Posted September 25, 2020 Share Posted September 25, 2020 (edited) 18 hours ago, Michael Hodgson said: They aren't worth the extra over the version that doesn't have a switch I never knew until now that there is a version without the switch. There you go, you learn something new every day. I prefer to use latching relays rather than microswitches, which I find fiddly to set up and potentially prone to moving out of adjustment. A relay fires when the point motor does, no mechanical linkage required. Edited September 25, 2020 by ejstubbs Link to post Share on other sites More sharing options...
Chris M Posted September 25, 2020 Share Posted September 25, 2020 I use latching relays with Peco point motors. I used SEEPs on my first N gauge layout in 2012 and in the light of that (rather disappointing) experience I have used Peco motors on later layouts. 1 Link to post Share on other sites More sharing options...
Michael Hodgson Posted September 26, 2020 Share Posted September 26, 2020 21 hours ago, ejstubbs said: I never knew until now that there is a version without the switch. There you go, you learn something new every day. I prefer to use latching relays rather than microswitches, which I find fiddly to set up and potentially prone to moving out of adjustment. A relay fires when the point motor does, no mechanical linkage required. Seep do a model PM1 with single pole switch on the PCB, PM2 lacking that switch and PM4 latching, with switch. I'm not aware of a PM3. Ideally one is likely to want double pole switch, one pole to wire the frog the other as a feedback to show which position the point is in. The downside of using relays rather than switches directly operated by the solenoid is that should the solenoid fail to operate, the relay will not reflect the actual position of the point. Of course you may be quite happy with that if they operate reliably. Of course if you attach more gubbins to what the solenoid has to shift, there is more chance of it failing to operate as reliably. Point indicators on the real railway show 3 conditions, Normal, Reverse or Wrong. The "Wrong" position shows briefly whilst a point is in the process of moving or not detected as locked fully over. This last option is mainly relevant to modellers if they use slow-acting motors rather than solenoids. Link to post Share on other sites More sharing options...
Pete the Elaner Posted September 26, 2020 Share Posted September 26, 2020 On 25/09/2020 at 07:22, Thebodger said: Well this is disappointing, i hoped unreliable meant weeks or months before failing not minutes can anyone recommend an alternative system that wont break the bank? I have bought some in the past for a friend's layout. I took 1 look at the switches & seeing how crude they are, I took the precaution of buying some microswitches. It cost less for each switch than the difference to have the included switch. I fitted 5 motors to a friend's exhibition layout then we tested them. 2 of them never worked. I found that disappointing but not really surprising. It took the 2 of us 35 minutes to fit & align the microswitches. These performed flawlessly for the 6-7 years the layout was on the exhibition circuit. I have heard people report no problems with them. Either they accept failures or the quality has varied over time. I was unimpressed. The motors themselves are very current hungry too. I found a CDU essential. Link to post Share on other sites More sharing options...
Thebodger Posted September 29, 2020 Author Share Posted September 29, 2020 Very helpful thank you all, the contact spray did the job for now but the latching relays, does anyone have a recommended brand or know of a guide to fitting them? Many Thanks Bodger Link to post Share on other sites More sharing options...
Theo Posted October 1, 2020 Share Posted October 1, 2020 I made up a wire thingy to centralise the operating pin when fitting seep point motors, ( see pic) which helps, but I agree with the erratic performance of the inbuilt switch. Most of my points are now tortoise, and the remaining seep ones are fitted with microswitches for drop power, and a second one for led indicayion 1 Link to post Share on other sites More sharing options...
MartynJPearson Posted October 2, 2020 Share Posted October 2, 2020 I've found that due to a general lack of woodworking prowess I have sometimes managed to move the Seep motor while screwing it to the board, mucking up the alignment. I've tried a new idea, using glue gun glue to hold them in place and once that is dry screwing them to the board - although I have left one to see how it fares with just the glue and no screws. Only challenge is getting the glue to flow uphill if you are working upside down on the bottom of the board, but I overcame that by using a strip of wood as a spatula to apply the glue. Link to post Share on other sites More sharing options...
ejstubbs Posted October 2, 2020 Share Posted October 2, 2020 See here for a simple but highly effective "seepeggy" tool for ensuring that the actuator rod is centred when fitting Seep point motors: 1 Link to post Share on other sites More sharing options...
westernviscount Posted October 2, 2020 Share Posted October 2, 2020 I don't the science but a spacer between the motor and the baseboard often helps with this issue. 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now