Hunslet Engine Works in 7mm Scale

[Andy Ross]

I have ordered some diffuser sheet used by photographers which should be here tomorrow - we will see what that looks like. 

 

I am sure there will be several tweaks before we get the final solution. 

 

I am going to reposition the strip today to find the optimum position. 

 

[Andy Ross]

I have also done some more digging and found Amazon do a strip which is a continuous light and you can dim. So I have ordered a set which should also come tomorrow. 

 

 

[Andy Ross]

North Lights, mark two. 

 

After the first attempt to light the erecting shop from under the roof, I was not 100% happy. But I felt I was on the right track.

 

I had already decided that two strips of lights was two bright and if I went to one I could lift the bottom one up a bit further which would move it out of the field of view. 

 

I was also concerned that it was also still a bit too white. So I had look on Amazon and came across a version that provided on continuous light and was slightly yellow. They also came with a dimmer control.

 

 

The light in the shop were sodium and these were a more yellow/orange light. 

 

I have built up one of the assemblies. 

 

   

 

This gives off a far better colour of light. What I need to do is build some more assemblies to see how bright it will be with more than one. 

 

    

 

So Back to the laser cutter tomorrow. 

 

The boiler shop end will still need some thought but as I have said before, one problem at once. 

 

Andy 

 

 

Edited December 30, 2023 by Andy Ross

[Andy Ross]

So I have finished making all the Hat Structures for all the North lights section of the roof during the week.  

 

Each one has a LED strip fitted and there are small plugs and sockets between each one. 

 

 

The little plugs were a pain to connect but it was really the only way to do it. 

 

 

When everything is painted and these go on for good the plug should tuck away behind the purling out of site. 

 

This has worked out really well, even when I turned all the garage lights off, you can see how well that end of the layouts illuminated.

 

 

I also believe we can do something similar in the boiler shop roof but that might need to wait for now. 

 

I am really pleased with this, especially y with the colour of the light. its not too white and gives the look of the sodium lights we had in the real shop. 

 

There is one issue we have found, all this continues damp weather has not been kind to the layout. The garage has proven this winter to be far more damper than previous years and this has caused a lot of the Nickel Silver structure to go black and patchy, it is particularly bad on the doors. I am sure it will be ok but it has emphasised the need to get everything painted this summer. I will have a go at cleaning this all up before Easter. 

 

 

Once everything is painted I am sure it will be ok.  

 

Next job all being well is to get the new fiddle yard up and sort the last bit of track out when the bits arrive from C & L. I then need to sort some permanent wiring out as it is all a bit temporary at the moment.

 

Andy

Edited January 6 by Andy Ross

[Andy Ross]

Just before Christmas I picked up the fiddle yard base board from my good friend Peter Kirmond. The intention was to get this up and fitted over the holidays and get the track laid.  I thought I had the rail and sleepers to do this, but this was not the case so this was put on hold while I ordered the parts. These took longer to arrive than I hoped and in the meantime I was taken ill which stopped almost everything for a couple of weeks and to be fair I am still not 100%. 

 

Despite this, today with Jills help, we managed to put the board up and later in the day I glued all the sleepers down. If its not too cold tomorrow I will fit the rails. 

 

 

This board is 1m long making the total layout length 4m which almost fills the garage. 

 

 

I had also decided that as this is only to run locos and the odd wagon on and off scene, most of which will be rigid six or four wheelers, there was no point messing with sector plates or point-work, as we can just lift the stock on and off as and when we need them. 

 

This will also be left open to view so the different loco types can be seen when they are not on the test track or in the erecting shop. 

 

The screen for the slide show will also be mounted on this board. 

 

Andy

 

 

 

 

Edited January 27 by Andy Ross

[Fishplate]

Hope you feel better soon Andy. 

 

All looking good.

[Andy Ross]

Slow progress over the last two weeks in garage due still not being 100% well. But I have managed to solder the rails in place, and today I found and fitted the strip for the check rail across the joint. I also took the opportunity to Ballast this short section. God knows how long it is going to take the glue to dry with the cold weather. 

 

 

 

In parallel with this I have been busy doing drawings to send for etching to help add to the variety of parts in the boiler and erecting shop. One etch is just general parts for the structure etc, but the second is far more interesting with cabs and casing parts for two very different locos - can you work out what they are?

 

 

If you want to see the layout in various stages there are a couple of outings coming up. 

 

Narrow Gauge North is on the 9th of March at Pudsey Civic hall, Leeds. I will be putting on a demonstration stand which will be based around the narrow test track board. I will not be taking the main board with the cranes etc. but there will still be plenty to see.

 

Easter at York will see the first show for the complete layout, all be it as a work in progress. On saying that it will all be operational. This will be a major milestone in the development of the layout.

 

Andy 

 

 

[Andy Ross]

Over the last few weeks there has been various activities across the layout, see below. 

 

I have been drawing parts to help fill different areas of the layout. Most of which have already been produced with the 3d printer. 

 

1. Wheel sets for the wheel shop . 

 

   

 

These are for the big Scunthorpe Bo Bo. What I am particularly please with is that I have cracked drawing gears. 

 

2. Fiji Loco frame 

         

 

This will fill a corner in the boiler shop. 

 

3.  300hp Mines bogie frame

    

 

These will go in the erecting shop.

 

4. Blocks, angle frames and bed plates.

 

 

These are needed for the boiler shop and will be used to position fabrications. 

 

I have also been working on motorising one of the MOD locos so it can be lifted onto the test track and run up the yard on test. 

 

 

The motor will fit up int the fuel tank. I have had to be a bit brutal with one of the ballast weights in the frame.

 

 

 

Still a bit more to do but I am getting there. 

 

I have also made a start on the wiring.  Compared with some layouts there is not a lot to do and at the moment I still have to finalise control panels. I need to operate all the layout to understand what needs to be on each panel or if we can do it all on one. 

 

Some can be done properly now such as under the layout. 

 

 

I have also worked out how to switch the rails to the power on the test track. This now has a rotary switch.

 

     

 

Position 0 - Turns all the Test track off 

Position 1 - Standard gauge and 5'6" gauge 

Position 2 - 2' gauge 

Position 3 - 2'6' and 3' gauge

 

This will be mounted for York in a temporary enclosure. 

 

I have also been looking at the boiler shop roof and I think I have a plan to get some lighting added to this area. 

 

More updates over the next few weeks. 

 

Don't forget the test track board will be at Narrow Gauge North at Pudsey Civic Hall on the 9th March.  

 

The complete display will be at York over Easter. 

 

Andy 

 

 

Edited February 25 by Andy Ross

[Andy Ross]

Apologies for the lack of posts recently. There has been some activity but at a reduced rate due to ongoing issues recovering from Shingles. 

I took the test track board to Narrow Gauge North at the beginning of the month and this was well received.

 

We are now on the last push to get the complete layout ready for York which is less than a week away. 

 

All the wiring is (I believe) complete and there will be a final test on Tuesday. 

 

One of the main jobs still to do was to get some sort of lighting into the Boiler shop roof. 

 

This also means I had to sort the removable section by cutting the longitudinal beams and finding a way to secure it in place. 

 

 

It's been a long time since I had this much access into the main shop. 

 

The roof lips under an angle on the wall side, and the solution on the other side is magnets. 

 

The magnets are mounted in some special sections I made on the filament printer. 

 

In the bottom edge of the roof panel is the opposite magnets but these are behind a 2mm layer of plywood to stop them locking too tightly together. 

 

The LED light strips are mounted on another 3d Printed section that positions them behind the top of the roof truss. 

 

 

 

From the viewing end these should not be too noticeable.

 

The top section will be glazed.

 

You will also notice the roof panels are all done with all the layers of ply for the inner structure. These take hours to cut.

 

I have also been fitting chips into a couple of locos and I am still on with getting the MOD loco working but more on that later. 

 

We also realised we did not have any sort of name plate for the layout. 

 

I mention this to Jill and when I got home form work on Friday she had come up with a design based on the Hunslet works plates. I cut some ply to mount it on and Jill used the Cricut to do the rest.

 

 

If you come to York over Easter please say hello. We will be on the first floor mezzanine with the demonstrators as we are still very much a work in progress. 

 

Hope to see you there. 

 

Andy 

[Andy Ross]

Quote

 

Last push for York.

 

So apart from crating up the main board and repacking all the loco parts etc. for an operating layout rather than a demonstration stand, we are all ready for York at the weekend. 

 

As seen in the previous post, Jill had made a name plate for the layout but were to put it?  The simple solution was a plate stand and for it to sit on the fiddle yard. 

 

I also want to continue running the slide show - so were to put the screen? 

 

Again this can go on the fiddle yard, but the original support leg fowled the track - so this was shortened and I printed a support on the filament printer.

 

 

The only other thing I wanted to do was mock up how the floor is going to work with the wood block and concrete floor. 

 

I had done the drawing for the parts last week. I had also engraved a sheet of 2mm ply with the block work. I then cut the parts for the walkways and under the benches from this sheet. To get to the 5mm track level there is 3mm foam board under the 2mm ply. At the moment this is all held in place with double sided tape

    

 

 

This has come out far better than I expected. Obviously once it is in place for good it will all be weathered down. It will now be interesting to see how this will look with all the kit in the shop. 

 

As I have said before if you come to York, please say hello and if you have any questions please do not hesitate to ask. 

 

Andy 

 

 

 

 

[ColinK]

I hope you’ve fully recovered from your shingles, a very nasty disease.  I’m just over shingles on my face, relieved that I didn’t loose my sight.

[Andy Ross]

I was lucky as I did not get it on face. But 10 weeks in and nerve pain has not gone away. 

[St Enodoc]

4 hours ago, Andy Ross said:

I was lucky as I did not get it on face. But 10 weeks in and nerve pain has not gone away. 

They've just released a new vaccine over here, for over-65s. I've had my first shot with a follow-up due two months later.

[Barry O]

On 28/03/2024 at 03:20, St Enodoc said:

They've just released a new vaccine over here, for over-65s. I've had my first shot with a follow-up due two months later.

We have had one here for a while. It was for over 70s but then it turned into anyone who was 65 last year. Missed that cos I am not 65 or over70.. true British medical logic...

 

Baz

Edited April 6 by Barry O
Spullung

[Fishplate]

12 hours ago, Andy Ross said:

if you come to York, please say hello

 

Planning to be there on Sunday. Will come and say hello. Looking forward to seeing this in 3D.

 

John

[Andy Ross]

5 hours ago, St Enodoc said:

They've just released a new vaccine over here, for over-65s. I've had my first shot with a follow-up due two months later.

I have to wait another two years for jab.  

[Andy Ross]

Hunslet Works all set up at York Model Railway Show..

Come along and say hello. 

 

 

 

 

 

 

[chipbury]

Looks fantastic - you've done a lot since it was at Larkrail.

I see on the display screen on the layout a vehicle that looks like an original liveried Tyne and Wear Metro - am I mistaken (or if not what's the story of it being in the works?).

 

Thanks

 

Chris

[Andy Ross]

Hi 

 

You are not Mistaken.  It is 4083 which had collided with a bus on a level crossing. 
 

it was the first passenger vehicle we did any work on at Hunslet. It lead to a lot of similar work for London Underground and we also refurbished the two prototype Tyne and Wear units. 
 

Andy 

Edited March 30 by Andy Ross

[Fishplate]

Nice to meet you and chat at York on Sunday, @Andy Ross and see your layout (very) close up. Excellent. I must have visited at least three times 😁

[Fishplate]

A group of pictures as well. Superb modelling. 

 

 

 

[03060]

3 hours ago, Fishplate said:

A group of pictures as well. Superb modelling. 

 

 

 

Those last 2 photo angles do it for me, photoshop them into sepia and you've invented time travel between you !

[Fishplate]

4 hours ago, 03060 said:

Those last 2 photo angles do it for me, photoshop them into sepia and you've invented time travel between you !

 

I'm afraid I don't have the technology to do that. Happy for someone else to have a go. I'm not sure if @KNP or @Gedward follow this topic ?

 

If they didn't before, I've just gently knocked on their doors. . . . 👋

[Andy Ross]

Based on the comments above I have cropped and adjusted the two images. 

 

 

 

They look quite convincing. 

 

Photo of real shop below.

 

[Gedward]

 

Edited April 6 by Gedward