Phil Bullock

Great news are you there Saturday?

Nothing about a dreamy Caramel then?

The burning question is how many slices of millionaires shortbread are needed on the stand at Warley!

The tiniest amount of gel superglue… applied with a pin …. On the edge of the grille recess. Just make sure they are on the right way around … rivets on the frame on the outside

Ah where was that then?

And it’s why ECoS now chucks out 7 amps…

Caerphilly?

Yes indeed the Deltic does …. Which makes it a better comparison

Was that on an HST ? Plainly not an of - fish - ial arrangement then! 😉 Or was it from Llangammarch Wels? Wels fish

Do those locos have stay alives?

Very nice! Wonder if the CBAs are any closer ?

Absolutely! Often seen on the triple headed iron ore trains to Llanwern …. Before that on Waterston to Albion tanks …. And they started off as lickey bankers when first delivered.

1965 picture of the Worcester train on This page There always seemed to be a redundant loco tender with this crane

They are the frost grilles which go over the radiator slats. Name is self explanatory..

D6702 drifts south through Wadborough today…

There’s no need to enlarge any holes on my D6702 … all the pipe work is a snug fit and is easily secured with a tiny dab of cyanoacrylate. With the buffer beam deeply recessed it is easier to fit the detailing with the body off … you can see what you are doing then. Fit the buffer beam end of the MU jumper too …. Then refit the body before plugging the jumper in to its body mounted receptacle. Whilst you have the body off fit your crew too… What a cracking model!

Would a merchandise wagon generally have drop sides and rigid ends? Whereas a mineral might generally have small side doors and an end tippler door?

A couple of spots of glue and glaze holds them in place robustly but will allow removal if you want to change the codes again

I gave a talk to the Worcester Locomotive Society Tuesday last … a very enjoyable evening, about 80 ex and current railwaymen and enthusiasts present. Took the opportunity to explore two points …. D9506-9 May have been allocated to Worcester on paper but they were never actually on the ground and As Mike Thomas mentioned to me in his notes up this thread they did work up to Worcester from Gloucester but only for a short time after steam finished until replaced by NBL type 2s … so that’s 1966 to 67. Cheers

Great got it thanks was just about to reach for the Xurons! The two bars in the accessory pack complete the bogie frame at the front once the kinematic couplings are removed…

Anyone else looking at removing the kinematic couplings? Have undone the two little screws visible behind the buffer beam but that doesn’t seem to release them….

Well said Jeremy…. Totally agree!

Done headcodes on one end of D6702. Have to say this loco wins the prize for the easiest to change! As suggested earlier finger nail leverage removes the outer frame of the headcode box. It is retained by two small pins which will either come away cleanly with the outer frame or snap off. You can see the remains of the snapped off ones above and below the 11 headcode in this photo… the pins came out cleanly on the other side. Underneath is a piece of glazing which is an interference fit and under that are the self adhesive headcode digits on a lovely metal frame. I peeled the old ones off with the help of a pin and replaced them with digits off the excellent included sheet. I then reassembled with a couple of tiny drops of glue n glaze either on the pins or on the frame if the pins had snapped off in their holes . And jobs a good un! Scunthorpe to Newport ADJ bolster Es loaded with 4 inch bar going south… 8E63 in the opposite direction, 16 tonners Radyr to Scunthorpe 16 tonners loaded with coking coal. A pretty convincing pair of workings for a Tinsley split boxer to appear on Abbotswood

Not unique …. Stands for no boiler. Although as modelled the boiler port is plated over the safety valves … the two small protruding items in front of the port … are still present. The reference photo Here still has a steam heat bag too so it may well be that NFB would be more accurate …. No functional boiler … although that could be open to misinterpretation…

Is my first job. Initial investigation suggests the frames are an interference fit… finger nail enough to budge them. Just beware of the superb detail on the boxes and frames