RMweb Gold Barry Ten Posted November 27, 2022 RMweb Gold Share Posted November 27, 2022 Piicked one up at Warley. Mine was initially hesitant over Settrack points and somewhat jerky, but after a bit of a thrash around the circuit, it quickly settled down to being slow, smooth and very reluctant to stall. It certainly is a stunner of a model and one of the most charming loco releases I've seen. Link to post Share on other sites More sharing options...
happyChappy Posted November 28, 2022 Share Posted November 28, 2022 12 hours ago, Barry Ten said: Piicked one up at Warley. Mine was initially hesitant over Settrack points and somewhat jerky, but after a bit of a thrash around the circuit, it quickly settled down to being slow, smooth and very reluctant to stall. It certainly is a stunner of a model and one of the most charming loco releases I've seen. Thanks Barry. I'm always interested to hear how new locos actually run rather than how perfectly formed they are. Seems like this achieves both which is excellent news. 1 Link to post Share on other sites More sharing options...
Markn Posted November 28, 2022 Share Posted November 28, 2022 On 23/11/2022 at 09:31, happyChappy said: Good to see the excellent quality of the chassis with decent wheel bearings and fitted flywheel. As there must now be a fair number of these locos actually out there would anyone care to comment on their slow-running capabilities? There seem to be a few possible wheel quartering issues with the new large Hunslets so I'm wondering if these quarry Hunslets are similarly affected? Slow reply sorry but yes it runs very well now. I say now, as I did have to clean the contacts and make sure they were all touching the wheels. I've had to do this on the last 2 double fairlie I've bought aswell. Haven't heard anyone else complain of the same, so it could just be a me problem. Link to post Share on other sites More sharing options...
friscopete Posted November 28, 2022 Share Posted November 28, 2022 MIne was a bit hesitant intially but I teased out the rear pickups with my scalpel blade and its runs fine now .Its a miniature work of art. . Link to post Share on other sites More sharing options...
happyChappy Posted November 29, 2022 Share Posted November 29, 2022 Thanks for both the above replies. Although all my current locos are diesel I'm so tempted by such a cute loco. Good running characteristics are an extra encouragement. Slight problem is my MOD-based layout has absolutely no steam facilities and, in any case, steam locos and explosives storage aren't a good mix! Link to post Share on other sites More sharing options...
didcot Posted December 1, 2022 Share Posted December 1, 2022 My Britomart arrived today. Absolutely stunning. The level of detail is incredible. Took longer to get the box open more than anything. Very pleased with it. Gave it a quick run on a spare piece of track. As some have mentioned it also has a slight tight spot. More noticeable in a slow crawl and more in reverse. It does lift a wheel slightly at this point. I thought it was something on the track. A small drop of oil on the motion has improved things. It runs quite smoothly with the knob at the 3 o'clock position on my H&M2000. I will chip it and run around on the layout over the weekend. Looking forward to Alice arriving. Link to post Share on other sites More sharing options...
RMweb Gold Barry Ten Posted December 1, 2022 RMweb Gold Share Posted December 1, 2022 Here's a short vid of mine on a circuit of set-track. I slowed it down right at the end to show it creeping through a dead frog point quite nicely. 7 Link to post Share on other sites More sharing options...
RMweb Premium nightstar.train Posted December 3, 2022 RMweb Premium Share Posted December 3, 2022 I picked up Britomart at Warley, and have only just had a proper chance to run it. Unfortunately my one is very stuttery at low speed, even after a good thrash around the test loop. Frequently stalls with the controller on 30% power. Can others who've had one comment on if I should try and fix this myself, or should I return it? Luckily I've kept the receipt! Quite disappointed TBH, doesn't run nearly as well as my Fairlie, or my Liliput O&K diesel. Link to post Share on other sites More sharing options...
RMweb Premium cnw6847 Posted December 3, 2022 RMweb Premium Share Posted December 3, 2022 7 hours ago, nightstar.train said: I picked up Britomart at Warley, and have only just had a proper chance to run it. Unfortunately my one is very stuttery at low speed, even after a good thrash around the test loop. Frequently stalls with the controller on 30% power. Can others who've had one comment on if I should try and fix this myself, or should I return it? Luckily I've kept the receipt! Quite disappointed TBH, doesn't run nearly as well as my Fairlie, or my Liliput O&K diesel. I read elsewhere that a persons Britomart didn't have all the pick ups touching the wheels but i'm not sure that would cause that much stuttering. Personally I think i'd return it. A shame as most people are saying how good they are. Link to post Share on other sites More sharing options...
vaughan45 Posted December 3, 2022 Share Posted December 3, 2022 (edited) 11 hours ago, nightstar.train said: I picked up Britomart at Warley, and have only just had a proper chance to run it. Unfortunately my one is very stuttery at low speed, even after a good thrash around the test loop. Frequently stalls with the controller on 30% power. Can others who've had one comment on if I should try and fix this myself, or should I return it? Luckily I've kept the receipt! Quite disappointed TBH, doesn't run nearly as well as my Fairlie, or my Liliput O&K diesel. The first one I purchased was jumpy and was returned to the retailer, the replacement one less so, particularly once run in for the recommended amount of time. I think the issue may be due to the slightly imperfect quartering of the outside cranks on some models. Strangely once it was fitted with the appropriate Bachmann (Zimo produced) decoder and running on DCC, the performance was transformed, and it now will come down to a slow crawl suitable for shunting. I suspect this may be due to decoder BEMF micro-managing the power requirements to maintain a constant speed. Edited December 3, 2022 by vaughan45 2 Link to post Share on other sites More sharing options...
Hiesler Posted December 3, 2022 Share Posted December 3, 2022 I also purchased a Britomart which had a tight spot that did not improve after 2 hours of running in. I exchanged it for another one (I can't recall ever having to return a model before) and it was better, but still seems to occasionally have the same issue (at the same point of rotation as well). I do hope a decoder will improve running, but generally a loco should not have to rely on one for acceptable running. I can't find the Zimo decoder in stock anywhere (I gather the Bachmann one is the same, but at a higher price) so the jury is still out on this. I appreciate these are small locomotives, but my expectations are high after seeing how my Bachmann N gauge Percy performs which is a similar size. I am now hesitant about the new Penrhyn Hunslets, as videos online also show mixed running qualities, which is a shame as I'd really like the tender versions when they inevitably happen. Link to post Share on other sites More sharing options...
didcot Posted December 3, 2022 Share Posted December 3, 2022 Having looked at the outside cranks with a magnifying glass I think the axle is splined. Which is what I would have expected rather than a push fit. It does mean that trying to tweak the quartering at home is a non starter. Mine is much better having been run in. 1 Link to post Share on other sites More sharing options...
vaughan45 Posted December 3, 2022 Share Posted December 3, 2022 (edited) 2 hours ago, Hiesler said: I appreciate these are small locomotives, but my expectations are high after seeing how my Bachmann N gauge Percy performs which is a similar size. I am now hesitant about the new Penrhyn Hunslets, as videos online also show mixed running qualities, which is a shame as I'd really like the tender versions when they inevitably happen. Based on the two I have, the running of these was ok 'out of the box' and slow speed running is good now they are both run in. Both were purchased from shops rather than by mail order, so the performance at all speeds could be tested before leaving. However, I appreciate that is not easy where there is no 'local' model shop. Edited December 3, 2022 by vaughan45 Link to post Share on other sites More sharing options...
Butler Henderson Posted December 3, 2022 Share Posted December 3, 2022 Derails test ran mine before despatch. 1 Link to post Share on other sites More sharing options...
RMweb Gold Roy Langridge Posted December 3, 2022 RMweb Gold Share Posted December 3, 2022 1 hour ago, Butler Henderson said: Derails test ran mine before despatch. That is where mine (a Christmas present) is coming from, so likewise, it should be good. Roy Link to post Share on other sites More sharing options...
friscopete Posted December 3, 2022 Share Posted December 3, 2022 16 hours ago, nightstar.train said: I picked up Britomart at Warley, and have only just had a proper chance to run it. Unfortunately my one is very stuttery at low speed, even after a good thrash around the test loop. Frequently stalls with the controller on 30% power. Can others who've had one comment on if I should try and fix this myself, or should I return it? Luckily I've kept the receipt! Quite disappointed TBH, doesn't run nearly as well as my Fairlie, or my Liliput O&K diesel. My one was a bit like that but I just opened up a rear pickup with the flat of a a scalpel blade poked behind to just push it out a tad and all is now perfect . 1 Link to post Share on other sites More sharing options...
Erichill16 Posted December 3, 2022 Share Posted December 3, 2022 Mine’s had no problems with pickups, it’s the tight spot when travelling chimney first that’s the problem with mine. Despite running in and a bit of lubrication it’s not getting any better and as it’s by far the worst performer in my fleet I’m going to see about getting it changed. Link to post Share on other sites More sharing options...
RMweb Gold PaulRhB Posted December 4, 2022 RMweb Gold Share Posted December 4, 2022 8 hours ago, Erichill16 said: Mine’s had no problems with pickups, it’s the tight spot when travelling chimney first that’s the problem with mine. Despite running in and a bit of lubrication it’s not getting any better and as it’s by far the worst performer in my fleet I’m going to see about getting it changed. Its probably quartering my bigger Hunslet Blanche has had to go back for that. When it’s correct they are very sweet runners 👍 1 Link to post Share on other sites More sharing options...
SomethingTrainLover Posted December 6, 2022 Share Posted December 6, 2022 Got my Britomart in Friday. Given it's a Christmas present, figured it would be wise to inspect it and give it a test just in case. Sadly, Noticed a glue stain on the tank, the funnel was loose and not seated fully in the base so sat at a noticeable angle and with a noticeable gap between the base and funnel. And the left hand cylinder was glued slightly wonky, so it pointed inward and this then brought the crosshead awfully close to the crankpin. Running was a bit lumpy and there was definitely a sort of rubbing-friction noise that while not horrible, was, again, noticeable. I mean as far as quality control slips, it could be far far worse lol. But I have decided to return the model and ship it back for a replacement Britomart, as I do still want the engine. In spite of the example I got, I still think it is a lovely little model and I'm looking forward to my replacement one, even if I probably won't get it in time for Christmas at this rate. 5 Link to post Share on other sites More sharing options...
SomethingTrainLover Posted December 6, 2022 Share Posted December 6, 2022 (edited) Deleted cause it was a duplicate Edited December 6, 2022 by SomethingTrainLover Link to post Share on other sites More sharing options...
didcot Posted December 10, 2022 Share Posted December 10, 2022 Finally got around to chipping my Britomart today. Its not exactly clear which way up the Bachmann chip goes, but second time lucky. It wouldn't run. A quarter turn and stop. Give it a nudge same again. Even increasing the power had no affect. I spent ages checking the pick up, took the motor out to check for tight spots in the motion. Nothing obvious until I changed the start voltage CV setting and it took off like a Smokey Joe! I've tweaked the start voltage and acceleration settings. It's alot better. With the body shell off I was limping in reverse, lifting a wheel set. But once the body shell was back on it ran almost perfectly. Still a bit tight, but crawls along much better now. I will hone the settings once it's had another good run. 2 Link to post Share on other sites More sharing options...
RMweb Premium figworthy Posted December 12, 2022 RMweb Premium Share Posted December 12, 2022 A quick question if I may. Could some kind soul have a quick measure up and let me know how high Britomart is above the rail head. Thanks Adrian Link to post Share on other sites More sharing options...
RMweb Gold Derails Models Posted December 13, 2022 RMweb Gold Share Posted December 13, 2022 (edited) 14 hours ago, figworthy said: A quick question if I may. Could some kind soul have a quick measure up and let me know how high Britomart is above the rail head. Thanks Adrian 35mm on a flat surface. 🙂 39mm when sat on Peco track. Edited December 13, 2022 by Derails Models 1 1 Link to post Share on other sites More sharing options...
RMweb Premium figworthy Posted December 13, 2022 RMweb Premium Share Posted December 13, 2022 9 hours ago, Derails Models said: 35mm on a flat surface. 🙂 39mm when sat on Peco track. Many thanks for that. Adrian Link to post Share on other sites More sharing options...
LNERandBR Posted December 14, 2022 Share Posted December 14, 2022 https://railsofsheffield.com/blogs/news/three-oo9-locos-incoming Rails reporting that Nesta and Dorothea are on their way shortly. 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now