Carnforth
Members-
Posts
259 -
Joined
-
Last visited
Content Type
Forums
Blogs
Gallery
Events
Exhibition Layout Details
Store
Everything posted by Carnforth
-
Same here with primers, some sold as etching but do not but I got this from Halfords the other week, grips like hell even though it's not advertised as etching. Nice satin finish and being black, great for chassis, wheels etc. serves as top coat. Previously I was buying Clostermann which is very good but I had to buy volumes to get it couriered to me.
-
Fibreglass pencil refills
Carnforth replied to Richard_A's topic in Modelling Questions, Help and Tips
I get the firm, effective ones from Squires, I think they term them as German. -
Prototype for everything corner.
Carnforth replied to jonny777's topic in UK Prototype Discussions (not questions!)
Standard 5 73014 has found itself coupled to a black tender when captured at Oxford on 13th September 1964. (John Calton) -
Prototype for everything corner.
Carnforth replied to jonny777's topic in UK Prototype Discussions (not questions!)
I use it as flux, suitably diluted. works a treat! -
Paint stripping with evidence.
Carnforth replied to LMRT's topic in Modelling Questions, Help and Tips
Seconded! -
If a rattle can and you have Motor Factors near you that will mix paint, I used RAL 3005 after researching. (As in picking the brains of others )! HTH
-
Here is a copy of my post from 2009 when the first batch were available. It may or may not help you. Prices and suppliers no longer valid but it gives you an idea. On 25/10/2009 at 10:47, Carnforth said: Mornin. Here should be brief, edited resume of what I did to 2 of these. This applies to the first issue and I posted it on another forum which was active on this topic at the time. Hope it is if some use. Steve I've just re-motored two of these for a friend with Mashima Flat Can 16/28s. ?? 20.50 each inc p+p from CometModels.This gives you as much quality motor as you can get in very easily. The flywheel bores need opening out to 2mm, and there's a small locating pip which needs removing from the chassis casting. The top plastic half of the motor mounting clasp can still be used by careful use of the 4 screws, run only partway in. The other problem which occurs with this model can be tightness of the gear tower assembly. I removed the brass worm and its attendant bearings,note the flats filed on the top edge to stop the bearings from spinning,( there was no end-float between these three parts, and the stub axles were a little too snug in the bearing bores). The inner faces of the bearings were dressed back a little and the bores opened out likewise. Both are now re-assembled and running in lovely. Dead slow crawl at 1v, whereas the motors supplied wouldn't even run with no load at less than 6v and sounded like an angry wasp. Shouldn't be necessary, of course and I' m glad I didn't wait all that time for them to appear with these faults. Poor assembly coupled with an awful motor! That said, it's a nice looking model but runs like a dog, unless you've been VERY lucky. Steve
-
-
Building supports
Carnforth replied to Ben Forster's topic in UK Standard Gauge Industrial Modelling
I think Railtec do sheets of rivets, in white rather than black.. -
Any reason why you cannot add wire pick-ups from the live side wheels soldered direct to the frames? Relying on bearings to flow current is fine once running but I wouldn't rely on that alone. HTH
-
BR 16t Minerals, By Accurascale
Carnforth replied to Accurascale Fran's topic in Accurascale / Irish Railway Models
Here's one that I built for one of the service crew of 46441about 35 yrs ago, I did him one in black too. He who pays the piper !! -
BR 16t Minerals, By Accurascale
Carnforth replied to Accurascale Fran's topic in Accurascale / Irish Railway Models
Betty Beet's Ivatt CL2 46441. Presently resides at L&HR. -
They both have different minimum landing sizes, not sure what they are now but for Dabs ( we called them Garves) it is quite small.
-
Soldering Chips and Stay Alives on small decoders
Carnforth replied to woodenhead's topic in DCC Help & Questions
Agreed, once you've removed the iron coating on Antex bits, they're on a short lifespan. -
BR Blue Spot fish vans - a question of numbers
Carnforth replied to Western Star's topic in UK Prototype Questions
This will help. https://paulbartlett.zenfolio.com/brfish -
Not seen it mentioned yet but I use Servisol switch cleaning lubricant in an aerosol, sprayed onto a cotton bud for wheels or a piece of card for railheads. First used it to improve continuity in the roller bearings in my Bacrus rolling road. Stated to improve conductivity. Works a treat, maybe similar to the WD products.
-
Bit late, this but Railmatch do Rail red in Acrylic, 18ml Plastic pot.
-
Very nice and thanks, may have been but it was a side on pic as I recall. I remarked at the time how well observed and modelled it was.